# Rangoli stencils to 3D print: tiles, centrepieces and border strips for Diwali

> A 3D printed rangoli stencil is a thin plate you sprinkle powder through. Tiles that join into a bigger rangoli, a round centrepiece with the family name and border strips for the doorstep: sizes, printing, washing and selling sets before Diwali.

Web page: https://stlmint.app/blog/3d-printed-rangoli-stencils

By Neha Parsiya (https://stlmint.app/authors/neha-parsiya). Published 2026-10-15, updated 2026-11-18

A [rangoli](https://en.wikipedia.org/wiki/Rangoli) is a floor pattern made at the threshold of a home from dry rice flour, coloured sand, powdered limestone or flower petals. It is usually laid outside the main entrance after the area has been cleaned, and it is mostly made for festivals: Diwali, Onam and Pongal above all. In Tamil Nadu the everyday form is the [kolam](https://en.wikipedia.org/wiki/Kolam), a line drawing of loops drawn round a grid of dots. Most of the time goes into keeping it even. Petals drift, the border spacing wanders, and the person with the steady hand is busy making sweets. A rangoli stencil fixes that. It is a thin plate with the pattern cut through it: lay it on the floor, sprinkle colour powder over it, tap and lift, and the pattern stays behind with sharp edges.

Stencils are flat, thin plates, so they print quickly, weigh little and post in an envelope. Here is what to make, how to print it and how to sell it.

## Three kinds of rangoli stencil

There are three useful kinds: tiles that join into a rangoli bigger than any one plate, a round centrepiece with the family name, and border strips for the doorstep. The [rangoli stencil](/designs/rangoli-stencil) covers the first two, and the [rangoli border stencil](/designs/rangoli-border-stencil) covers the third. Both are in [seasonal keepsakes](/designs/seasonal-keepsakes).

## Rangoli stencil tiles that join into a bigger rangoli

The square tile comes in five patterns: lotus, diya, peacock feathers, mandala and a South Indian kolam of loops round dots. Each tile has half a flower on every edge and a quarter of one in each corner. Lay two tiles edge to edge and the halves meet in a whole flower, so four tiles in a square, or nine in a grid, make one larger rangoli. You can also print one tile and move it along a tile at a time.

Sizes and build:

- **150 mm across by default**, adjustable from 80 to 200 mm, so it fits most printer beds.
- **A 1.2 mm plate** with a 3 mm frame round the pattern.
- **A 2 mm raised rib** along the frame that keeps a big plate flat and gives fingers something to lift. Set it to 0 for no rib.
- **Bridges 1.2 mm wide** by default, holding every island in place so the stencil is one piece.

## A round centrepiece with the family name

Switch the shape to round and the same patterns become a centrepiece for the middle of a rangoli, or a small rangoli on its own at the door. Type a family name or a greeting into the two text lines, for example "JOHNSON", or "Shubh" and "Deepavali", and it replaces the centre flower, with a ring of the pattern round it.

The lettering is stencilled too, so every closed letter (the middle of an A, O or R) gets a small bridge to keep it attached. That is why the font list is short and plain: four bold Latin faces. Hindi and Tamil lettering is not supported on the stencil yet, so keep names in English letters.

A round plate can also have a tab with a hole, so it hangs on a hook between festivals. Leave the tab off on square tiles you lay in a grid.

## Border rangoli stencil strips for the doorstep

The border stencil is a long strip with a motif that repeats along it. There are six motifs: paisleys, a leaf vine, diyas, marigolds, waves and Lakshmi's footsteps stepping in from the edge. A row of dots, dashes or scallops runs along both long edges, or you can leave the edges plain.

- **50 mm wide**, with a motif every 39 mm. Width and repeat are adjustable.
- **Up to 225 mm long.** Set the length to your bed; the strip takes as many whole repeats as fit. A 220 mm bed fits five.
- **1.5 mm thick** by default, up to 3 mm, with 1.6 mm bridges.
- **Dovetail ends.** One end has a dovetail and the other a matching slot, so strips key together and the motifs and edge dots stay evenly spaced across the joint. Choose square ends if you would rather butt them up.
- **A corner piece**: an L with a flower in the corner square and the motif down both arms, so the border turns round a rangoli or a doorway.

Four strips and four corners in one motif frame a square about 53 cm across, with room for a 40 cm rangoli inside.

## How to use a rangoli stencil

1. **Sweep the floor** and make sure it is dry.
2. **Lay the plate flat**, rib side up, so the flat face sits tight against the floor.
3. **Sprinkle from close above.** Use your fingers, a spoon or a tea strainer for fine rangoli powder or coloured sand. Cover every cut-out.
4. **Tap the plate** lightly a few times to settle the powder and shake off loose grains.
5. **Lift straight up**, by the rib or the edge. Sliding it smears the pattern.

For a second colour, sprinkle it by hand into the centre flower or the dots after lifting, or alternate two tiles in different patterns. For a border, lift the strip and lay it again just past the last motif, or key several strips together and do the whole step at once.

## Printing tips

- **Print flat with no supports**, the tile rib side up. Both designs are one colour and one piece.
- **PETG is the better choice.** Prusa's [PETG guide](https://help.prusa3d.com/article/petg_2059) notes its toughness and flexibility: it bends back instead of snapping when the plate is stepped on or flexed while lifting, and it rinses clean. PLA is fine for a stencil that is used for one season.
- **Keep bridges at the default width or wider.** Bridges under about 1.2 mm on the tile break when the plate is lifted. Widen the bridge on the border strip for a stiffer stencil.
- **Check the first dovetail.** Print one strip and push two ends together. If the joint is tight, raise the fit to 0.3 mm; if it is loose, lower it.

## Washing and storage

Tap the plate over a bin or outside to knock off most of the powder, then rinse it under cool water and wipe it with a soft brush or cloth. A drop of washing-up liquid lifts coloured powder that has stained the edges. Do not use hot water, especially on PLA: its [glass transition is around 60 to 65 °C](https://en.wikipedia.org/wiki/Polylactic_acid), well below boiling, and a thin plate warps there. Dry the plate flat. Store stencils flat, away from a sunny window.

## Selling rangoli stencils as Diwali sets

- **A family set:** four matching square tiles and a round centrepiece with the family name. The name is what makes it a gift, so it suits relatives and housewarmings.
- **A doorstep set:** four border strips and four corners in one motif. Diyas and marigolds are the general Diwali motifs; Lakshmi's footsteps suit the doorway on Lakshmi Puja, since a threshold rangoli is meant to welcome Lakshmi into the home.
- **A society or temple set:** several tile and border sets for a rangoli competition or an entrance. Quote per set at a few quantities.

When an order has a centrepiece for each family, for example a housing society giving one to every flat, collect the names as one list, one per line. On the Seller plan, paste it into **Bulk order** on the design and you get one file per name in list order. The [Diwali gifts post](/blog/personalised-diwali-gifts-to-3d-print) and [custom orders on Instagram and WhatsApp](/blog/custom-orders-on-instagram-and-whatsapp) cover taking orders and getting names approved.

On price, a set is several prints, so work from print time and filament per piece and add your margin; [how to price personalised 3D prints](/blog/how-to-price-personalised-3d-prints) walks through it. Stencils are flat and light, so they post in a stiff envelope; see [packing and posting small 3D prints](/blog/packing-and-posting-small-3d-prints).

## Lead times

List the sets three to four weeks before Diwali. Rangoli competitions are planned ahead, and families need the stencil a few days before the festival. Keep a few unnamed sets in stock and publish a last order date that leaves room for busy couriers.

The same stencils sell again for Pongal, Onam, weddings and housewarmings, so keep a note of every buyer. The [Diwali gifts ideas page](/ideas/diwali-gifts) has the stencils alongside hamper tags, name plates and other festival designs, and the [housewarming gifts](/ideas/housewarming-gifts) page suits families moving in over the festival season.

## Common questions

**What size is a rangoli stencil tile?**
150 mm square by default, adjustable from 80 to 200 mm. Four tiles make a 300 mm rangoli; nine make 450 mm.

**Will the middle of the pattern fall out?**
No. Every island in both designs is held by a bridge, so each stencil is one connected piece.
