Barber station organisers to 3D print: a tool rail, combs and a key holder

A barber tool holder for the wall with the shop's name across the top and a labelled peg for scissors, combs and clippers, plus the small things that go with it: a comb with the shop's number on the spine, a stand for each chair and a key holder for the back door.

Barber station organisers to 3D print: a tool rail, combs and a key holder

The counter under a barber's mirror is wet, covered in hair and full of tools. Before adding any organiser, it helps to know how shops are expected to handle tools between clients. Rules are set locally and vary. California's Board of Barbering and Cosmetology, for example, requires that all disinfected tools be stored in a clean, covered place labelled "Clean" or "Disinfected", with used tools kept apart until they are cleaned. Many US state boards have similar wording, and inspectors check it.

So an open wall rail is a working rack, not disinfected storage. It holds the tools in use at the chair and the things that don't need disinfecting (clipper guards in their packs, brushes, keys, spray bottles), and gets them off a wet counter. Disinfected scissors and combs still go into the covered container the local rules ask for. With that in mind, here is a barber station organiser that prints flat, the small pieces that go with it, and how a seller can offer them to the shops on their street.

The salon tool rack

The salon tool rail is a rail for the wall with the shop's name across the top and a row of pegs under it. Each peg has its own label: type SCISSORS, COMBS, CLIPPERS, GUARDS and BRUSH, and you get five pegs, each with its word. It takes up to seven, one for each label, and fewer on a narrow rail, since each peg needs about 26 mm. With no labels typed it has three plain pegs.

Anything with a ring, a loop or a hole hangs on a peg: scissors by a finger ring, combs and brushes by the hole in the handle, clippers by their hanging loop. There is a dip near each peg's end so a ring settles into it. The pegs are 7 mm across and 11 mm deep, so check that a tool's ring is larger before you promise it will fit.

The rail is 120 to 245 mm across. It goes up with two ordinary screws through countersunk holes; on a mirror frame or on tiles, use fixings suited to the surface.

How the pegs stay in

Each peg has a wide foot. The pegs push through from the back of the rail and the feet sit in pockets there. Once the rail is screwed to the wall, the wall holds them in, so they can't pull out forwards. There is no glue.

Printing it

The rail prints face up, with no supports: the pockets for the pegs' feet are in its back and bridge across. The name and labels are a second colour on top after one filament change, so an ordinary single-spool printer does it.

The pegs print on a plate of their own, lying on their sides so the layers run along them. Print them in the rail's colour or the words'. If a peg is tight in its hole, raise the fit setting and reprint just the pegs.

The small things for the chair

A barber station organiser is more than the rail. Three pieces go with it:

  • A comb with the shop on it. The name comb has a name along its spine and comes as a pocket comb or a comb with a handle, with fine teeth, wide teeth, or half of each. The comb with a handle has the most room, so a shop can put its name and phone number on the spine and hand them out. Print it in PETG, which Prusa's PETG guide describes as tougher and more flexible than PLA: its teeth bend and spring back, where PLA can snap if it is sat on. A printed comb has layer lines, so it suits a giveaway or the customer's own pocket better than a shop comb that goes through disinfectant every day.
  • A stand for each chair. The chair station stand sits on the shelf under the mirror with the chair's number and the stylist's name.
  • Keys by the back door. The wall key holder is a name plate with one to twelve hooks under it, for the shop's keys, the till key and the shutter key, with the shop's name on top.

Selling to barbers

Sell the rail one per chair, with the barber's own name on each. A shop with four chairs is an order of four rails, four stands and a batch of combs. Hang a name comb on the rail when you show it, so the shop can see how a tool sits on a peg.

Combs can be a repeat order: a shop that hands them out with its number on the spine will want more. Price singles as a gift and batches by the plate. For one name per comb or one stylist per stand, paste one per line into a bulk order. Bulk orders and the right to sell the prints come with the Seller plan.

The salons and barbers page has the rest of what a shop can use, and 3D printed signs for salons and barbershops covers the price board and window sign that sell alongside.

The same rail works outside a barber's too: a stylist's own chair, a dog groomer's wall, or keys and leads by a front door.

Planning what to make next? Browse personalised print ideas by occasion, or work out prices, party orders and colour changes with the free maker tools.

Take your next custom order in minutes

Type your customer's text, send them a picture to approve, download a print-ready file.

Start selling

Keep reading