A birthday party set to 3D print: crown, cake topper, table scatter and wands with one name

Personalised birthday party decorations that all carry the same name and age: a crown for the birthday child, a hoop topper for the cake, scatter down the table and a bubble wand for every guest. What each piece is, how they print, and how to sell them as a set.

A birthday party set to 3D print: crown, cake topper, table scatter and wands with one name

A children's birthday party usually needs the same handful of things: something for the birthday child to wear, a topper for the cake, something on the table and a small take-home for each guest in the party bag. Before printing any of it, check three things:

  • Small pieces and small children. Table scatter is small enough to swallow. In the US, the rule for what counts as a choking hazard is 16 CFR Part 1501, the test for small parts in articles meant for children under 3. Keep scatter off tables where toddlers sit, and make take-home gifts one solid piece with nothing that can snap off.
  • Plastic and cake. Printed parts are not food-safe: Prusa's guide to food-safe FDM printing points to the layer grooves, which are almost impossible to clean. A topper sits on the cake and comes off before it is cut.
  • Heat. PLA softens above about 60 °C, so keep toppers away from lit candles and pieces out of a hot car.

Bought one at a time from different shops, party pieces rarely match. This set is four printed pieces that carry the same name, the same age and the same two colours: a birthday crown with the name across the front, a topper for the cake, scatter for the table and a bubble wand for each guest to take home.

The crown

The birthday crown prints flat as one thin band with the name across the front and the age on the middle point. The points can be balls, scallops or castle battlements, with jewels each side of the name. The name can be up to twelve letters and is fitted to the middle of the band, so a short name comes out biggest.

At 1 mm thick it bends round the forehead. Thread ribbon or hat elastic through the two holes at each end and tie it at the back, so it fits any head. Bend it gently the first time, with the lettering outwards; PETG is more forgiving than PLA. Leave the age empty and it does for a school play or a prom too.

The cake topper

The hoop cake topper is a ring with the name across it in script, a short line curved inside the top (HAPPY BIRTHDAY, HAPPY 40TH, ONE TODAY) and leaves, hearts or stars round the bottom. Two spikes go into the cake. Pick a hoop a little narrower than the cake: 130 mm suits a 15 to 20 cm cake, 90 mm a small one, 170 mm a large one.

A topper is a decoration, not a food-contact item. Wash it, and wrap the spikes in cling film or push them into drinking straws set in the cake.

Birthday table scatter with the age and name

The table scatter set is a handful of stars, hearts and discs with the age on them, mixed with little banners carrying the name, one in every five pieces. A set is ten to eighty pieces, and fifty fit on one plate at the standard size. Forty to fifty is enough for a table of eight.

The pieces are small, 18 to 40 mm across. Keep them off tables where children under three are sitting, and pick them up afterwards. Swept into a bag, the name banners keep for next year, with a new plate printed for the next age.

A wand for every guest

The bubble wand has a child's name down the handle and a star, heart, flower or ring loop with little teeth inside that hold the mix. It is one solid piece with no small parts to come off, and a hole in the handle takes a wrist ribbon. Make one for the birthday child and one for each guest, and the party bag has something in it that gets used. There is more on wands as favours in bubble wands for party bags and weddings.

Printing the set

Every piece prints flat, face up, with no supports. The colours are stacked layers: print the base, change filament when the lettering starts, and finish. No multi-colour printer is needed. Gold or yellow with a strong colour for the name suits the crown, and silk gold on the topper's lettering has a metallic sheen. Print two plates of scatter in different colours and mix them on the table.

The crown is thin and long, so a clean first layer and a bed that is level from end to end matter. Let the scatter cool before lifting it off the bed.

Selling it as a party set

Selling the pieces together saves the parent four separate orders. Ask for the name, the age and two colours, then print the crown with a ribbon already threaded, a topper sized to the cake, a bag of fifty scatter pieces and a wand per guest. For the wands, take the guest list and paste one name per line into a bulk order. Bulk orders and the right to sell the prints come with the Seller plan.

Home bakers are the other buyers: a topper with every cake order, and the crown and scatter as add-ons. The birthday party favours page has more pieces to put in the bags.

Planning what to make next? Browse personalised print ideas by occasion, or work out prices, party orders and colour changes with the free maker tools.

Take your next custom order in minutes

Type your customer's text, send them a picture to approve, download a print-ready file.

Start selling

Keep reading