# Flat number plates for housing societies: taking and printing a whole building's order

> How to sell matching flat number plates to a housing society: taking the flat list from the committee, samples, sizes that read from the corridor, mounting, pricing and delivery by wing. Plus decorative name plates for a family's own flat door.

Web page: https://stlmint.app/blog/flat-number-plates-for-housing-societies

By Neha Parsiya (https://stlmint.app/authors/neha-parsiya). Published 2026-10-15, updated 2026-11-18

When a housing society repaints its corridors or a builder hands over a new tower, someone on the committee is asked to sort out the flat number plates. They want every door to match and one supplier to do all of it. For a 3D printing seller that is one buyer, one design and anywhere from 50 to 500 plates. Below is how to take that order, and then the steadier sale that follows: a name plate for a family's own flat door.

## What a society wants from a flat number plate

Committees care about three things: every plate the same, numbers that read from the lift, and no mix-ups between wings. The [flat number plate](/designs/flat-number-plate) is built around that. The number fills the plate and the wing or tower letter sits apart from it, in one of four layouts:

- **Band**: a wide plate with the wing letter cut out of a coloured band on the left.
- **Pill**: round ends, with the wing in a solid disc.
- **Portrait**: a tall plate with the wing in a ring at the top.
- **Frame**: a plaque with a thin frame, the wing and number side by side, and the society's name set into the top edge of the frame.

The society's name runs underneath in small capitals, and a long name breaks onto two lines instead of shrinking.

## Take the flat list from the committee

The whole order rests on one list. Ask the secretary for every flat, one per line, written exactly as it should be printed:

```
A-101
A-102
A-103
...
B-1204
```

The wing is part of the flat text. Type A-101, B 1204 or T2-904 and the one to three characters before the dash, space or slash become the wing tag. C1102 splits where the digits start. A flat typed as plain 1204 is just the number. If the building has no wings, or uses labels like VILLA 27, turn the wing tag off in All options and the whole label prints as one number.

Before you accept the list, check:

- **One format throughout.** A-101, A 102 and A/103 all split correctly, but a mix looks careless. Pick one.
- **The count per wing** against floors times flats per floor. Lists often miss a duplex, a shop or the society office.
- **The society's name, typed once**, not read out over the phone, and whether they want the full registered name or a short form.

Our post on [avoiding misspelled names](/blog/avoid-misspelled-names-on-custom-orders) covers written approval, which matters more when 300 plates carry the same name.

## Turn the list into files

With the Seller plan, set the layout, colours and society name, choose **Bulk order** and paste the list. Each line becomes the flat number on its own plate, and you get a ZIP with one file per flat. Seller lists take up to 200 lines, so do a large society one wing at a time, which matches how you will print and deliver it.

## Samples for the committee

Committees decide in meetings, so give them something to hold. Print two or three samples of one real flat, say A-1204, in different layouts or colour pairs, so the committee picks the flat number plate design in hand. A sample taped to an actual door shows size and colour in a way a picture can't. Once one is chosen, note the layout, font, size and colours, and get a yes in writing.

## Sizes and reading from the corridor

The default plate is 120 x 60 mm and 3 mm thick, with the lettering raised 1 mm. On that plate a four-digit number comes out roughly 16 to 22 mm tall depending on the layout. For a yardstick, the US accessibility guide for signs asks for visual characters of [at least 5/8 inch (about 16 mm) when read from under 6 feet, plus 1/8 inch for every extra foot](https://www.access-board.gov/ada/guides/chapter-7-signs/). It is not a rule for Indian societies, but it is a fair test: the default number reads well from in front of the door and a few steps back, not from the far end of a long corridor. The portrait plate is 60 wide and 120 tall.

If the number has to read from the lift or down a long corridor, go larger: the long side goes up to 220 mm and the short side up to 120 mm in All options, and the number grows with the plate. Condensed fonts such as Big Shoulders fit a long number larger.

## Mounting: screws or tape

The default has two countersunk holes for 4 mm screws, so a flat-head screw sits flush with the face; use wall plugs on masonry. Many societies don't want doors drilled, and some flats are rented. Pick **tape** for a flat back with no holes and fix it with strong double-sided foam tape on a clean door.

## Colours that suit a building

High contrast reads best: white on charcoal, gold on maroon, green on cream. Look at the corridor first. Teak or dark laminate doors want gold or light lettering; white doors suit charcoal or navy. Avoid two dark colours, which vanish under a dim corridor light.

Print face up with a filament change at 3 mm, so the number, wing tag and society name come out in the second colour. PLA is fine for indoor corridors, but Prusa's material guide notes that it [softens above about 60 °C and degrades under UV light](https://help.prusa3d.com/article/pla_2062). For open corridors or ground-floor doors that get sun and rain, use [PETG](https://help.prusa3d.com/article/petg_2059), which Prusa rates for most exterior use, or [ASA](https://help.prusa3d.com/article/asa_1809), which it describes as suited to outdoor use because of its UV resistance.

## Pricing a society order

A committee wants one number per plate and a total they can put to the members. Work out your cost for one full bed (filament, printer time, your time), divide by the plates on the bed, then add margin. Our [pricing guide](/blog/how-to-price-personalised-3d-prints) walks through it.

Quote:

- **A price per plate**, with a lower rate past a quantity like 100 or 200.
- **Spares included**, about one per wing, for mistakes and damaged plates.
- **Screws and tape**, or say clearly that they are not included.
- **Fitting**, charged per plate, or left to the society's maintenance staff.
- **Later plates** for new flats or the clubhouse at the same rate.

Ask for an advance before printing a large run.

## Lead times and delivery by wing

Time one full bed of plates on your printer, then multiply. Several 120 x 60 mm plates fit on one bed; print a wing at a time so the set stays in order. The [batch printing guide](/blog/batch-printing-custom-orders) has a routine for planning beds. Quote a date with a few days of slack.

Deliver wing by wing. The committee sees progress, and a mistake in the list costs one wing's reprint at most. Pack each wing in its own labelled box, floor by floor, with a printed copy of its list ticked off, so whoever fits them can walk up the stairs with one box.

## Name plates for a family's own flat door

Families often want something of their own beside the society plate: a house number plate that also carries the family's name. It suits a griha pravesh (housewarming) gift at any time of year, and many families freshen up the front door before Diwali.

The [layered house number](/designs/layered-house-number) is that plate. It is 150 x 100 mm by default, adjustable from 100 x 70 up to 220 x 160 mm, with the number large in the middle and the family's name in script under it. The motif can be a **torana** of mango leaves and marigolds along the top, a pair of **diyas** or **rangoli** flowers beside the number, a leaf sprig, or a little house drawn round it. The outline can be rounded, arched, or a scalloped jharokha arch. The name can be typed in Devanagari, such as शर्मा निवास, and it is set in Noto Sans Devanagari automatically. A small line underneath can carry family members' names or a welcome.

It prints in two colours: a 4 mm plate and a 1.2 mm layer on top, with one filament change, and screw holes or a flat back for tape. Ivory on maroon and gold on deep green read well.

For a simpler plate with only text, such as THE JOHNSONS and FLAT 402, the [sign plate](/designs/sign-plate) takes up to three lines and can have two or four screw holes. It also suits the society office, the clubhouse and the security cabin, in the same colours as the flat plates.

## Finding the next society

Start with committee members you know and builders handing over towers, then show the next committee a photo of a finished corridor. The [housing societies and apartments](/ideas/housing-societies-and-apartments) ideas page has more designs for the building, and [housewarming gifts](/ideas/housewarming-gifts) has more for families moving in.

## Common questions

**What size should a flat number plate be?**
120 x 60 mm suits a number read from in front of the door. Go up to 150 or 180 mm long for long corridors or doors seen from a distance, so the digits grow with the plate.

**How long does a 300-flat order take?**
It depends on your printer and how many plates fit on a bed. Time one bed, multiply, and add slack for samples and committee approval, which often takes longer than printing.
