Gifts for book lovers to 3D print: a page holder, a bookmark and shelf dividers with a name

Three gifts for book lovers that carry the reader's name: a thumb book page holder that keeps a paperback open with one hand, a name bookmark, and shelf dividers for the books at home. What each one does, how to size it and how to print it.

Gifts for book lovers to 3D print: a page holder, a bookmark and shelf dividers with a name

People who read a lot already own the books they want, so gifts for book lovers tend to be the things around the book: something to hold it open, something to keep the page, something to sort the shelves. Those accessories assume a paper book, and most readers still use one. In Pew Research Center's October 2025 survey, 64% of US adults had read a print book in the past year, against 31% for e-books and 26% for audiobooks.

Size is the thing to get right. Paperbacks come in a few standard formats: the small mass-market or UK A-format book is 110 x 178 mm, with larger B-format and trade paperbacks above it, and hardbacks larger again. A page holder has to span the open pages, a bookmark has to sit inside the book without poking out too far, and a shelf divider has to be a little shorter than the books beside it. Here are three you can print with the reader's name on, starting with a thumb book page holder.

A thumb book page holder

A paperback wants two hands, and readers don't always have two free. The thumb page holder is a ring for the thumb with a wing each side. Put the thumb through the ring and rest the holder in the gutter of the open book; the wings lie across both pages and hold them flat while the fingers support the book from behind. It keeps the book open on a train, in a queue, in the bath or with a mug in the other hand.

The reader's name goes on one wing and a few words of your own on the other: ONE MORE CHAPTER, DO NOT DISTURB, or a book club's name. The holder can be wings, leaves or a plain bar, 100 to 170 mm across.

Size the ring to the thumb. Measure across the thumb at its widest joint and add a millimetre or two. 22 mm is a reasonable starting point for an adult; 18 to 20 mm suits a small hand, and 24 mm or more a large one. It is made for paperbacks; for a thick or tall book, choose the longest span so the wings reach further across the pages.

It is flat enough to post in a card, which makes it an easy present to send.

A name bookmark

The name bookmark is 150 by 35 mm, long and slim like a paper one, with the reader's name running down its length so even a long name gets big letters. It comes in two styles:

  • Tassel: flat, with a hole at the top for a tassel or a loop of ribbon, a ribbon-cut tail, and a vine, stars, hearts or diamonds down both edges.
  • Page clip: it slides over the top of the page and holds on, with a round head showing the reader's initial above the book, so the page can be found with the book shut.

Sold together, a page holder and a bookmark in the same colours make a reader's pair. Personalised name bookmarks has more on class sets and book clubs.

Shelf dividers for the books at home

For someone with full shelves, shelf dividers stand between the books with a tab sticking out past the spines. The words run up the tab and read from both sides, and a big letter or number can sit at the top.

A set of five with the reader's own headings, such as CRIME, POETRY, TO READ, or one per family member, turns a home library into something they can find their way round. Make each divider as tall as a typical book on the shelf, or a little less, and as deep as the book is wide less a centimetre. For small paperbacks that is about 180 by 110 mm, close to the A-format size above. Dividers can be an open frame, lighter to print and easy to grip, or solid.

Printing them

All three print flat, face up, with no supports. The colours are stacked layers with a filament change where the words start, so a single-spool printer does the job. The shelf divider prints with its back face down and takes two changes: one after the first three layers, so its back words show, and one when the front's words start.

  • Print one page holder first to check the ring on the reader's thumb. 4 mm thick is comfortable to hold; thinner flexes.
  • Rub the page holder's edge with a fingernail after printing to take off any burr.
  • For the bookmark, light letters on a dark base, or the other way round, read best: cream on navy, white on red, black on yellow.

Who they suit

Readers and commuters, new parents reading one-handed, book clubs and teachers. They are light and small, so they also work as stocking fillers; the Christmas stocking fillers page has more.

If you sell them, a book club or a class is one order: paste one name per line into a bulk order and get a file for each. Bulk orders and the right to sell what you print come with the Seller plan. Page holders can be sold by name at book fairs and craft markets, and by the dozen to book clubs.

Planning what to make next? Browse personalised print ideas by occasion, or work out prices, party orders and colour changes with the free maker tools.

Take your next custom order in minutes

Type your customer's text, send them a picture to approve, download a print-ready file.

Start selling

Keep reading