Gifts for knitters and sewers to 3D print: a row counter, a sewing gauge and a needle gauge
Christmas presents for people who make things: a knitting row counter with two sliding markers, a sewing gauge that holds a hem's depth, and a needle gauge with a swatch window, each with the maker's name on it. What each one does, how they print, and how to sell them.
People who make things are hard to buy for at Christmas. They have the yarn and the fabric, and they chose it themselves. Good gifts for knitters and sewers are the small tools they use every evening and keep losing.
It helps to know the measurements these tools deal in. Knitting needles are sized in millimetres and, in the US, by number, and the numbers don't always agree between makers: the Craft Yarn Council, which publishes the US industry standards, advises relying on the millimetre size on the packet. Patterns give gauge as stitches over 4 inches or 10 cm, and the Council's yarn weight table lists the usual ranges for each weight of yarn. In sewing, the measurement repeated most is the seam allowance: patterns for home sewers use 1/4 to 5/8 inch (6.4 to 15.9 mm), with 5/8 inch common in dressmaking and 1/4 inch in quilting.
Here are three tools to 3D print with the maker's name on them, starting with a knitting row counter.
A knitting row counter to 3D print
The knitting row counter has two rows of figures, tens over ones, with a marker under each that slides along to the count. Forty-seven rows is a 4 and a 7. It counts from 0 to 99.
At the end of every row, move the lower marker on one figure. When it passes 9, take it back to 0 and move the upper marker on one. The markers are a close fit in their channels, so they stay where they are put when the knitting goes down for the kettle, and end caps shut them in so they can't be lost.
The knitter's name runs along the top, and there is a hole for a stitch marker or a ribbon. The two small labels at the left can be changed too: ROWS and REPS, or two different pattern markers, for anyone who counts more than one thing.
A sewing gauge with a sliding marker
The sewing gauge is the short ruler from every workbox: inches in eighths along one edge, centimetres along the other, and a marker that slides along it and holds its place. It sets from 5 mm, under a quarter inch, up to the gauge's length, which is 10 to 20 cm.
It is for repeating one measurement many times: a hem's depth, a seam allowance, the gap between buttonholes, pleats and tucks. Set the marker once and use its edge against the fabric each time. The sewer's name goes at the end, which in a shared sewing room is how it comes back.
Be honest with the buyer about one thing. It is a marking gauge, not a precision instrument. It is only as accurate as the printer that made it, so check it against a steel rule before you sell it, and tell the buyer to use it for repeat marks, not for measuring a pattern.
A needle gauge with a swatch window
The knitting needle gauge has eighteen holes from 2 to 10 mm, each marked with its size, and can add US sizes from US 0 to US 15. Push a needle into the holes from the smallest up; the first it slides through without forcing is its size.
A ruler runs along the top, and a 10 cm (or 4 inch) window lets the knitter count the stitches in a swatch. It is one flat piece that fits a project bag's pocket. There is more on it, with sew-on labels, in gifts for knitters and crocheters.
How they print
All three print flat, face up, with no supports and no glue. The colours are stacked layers with a filament change, so no multi-colour printer is needed.
The needle gauge is one piece with one change, where the sizes start. The row counter and the sewing gauge need three filaments on an ordinary printer: the counter or the gauge with one change for the figures or the scales, and the markers (and the gauge's cap) printed on their own in a bright colour. A red marker on a white gauge is easy to read.
A few details from the design pages:
- The counter's figures are small, and the gauge's ticks are 0.8 mm wide. A 0.4 mm nozzle and a 0.2 mm layer print them cleanly.
- Print slowly round the needle gauge's holes, and check the 4 mm hole with a 4 mm needle before printing a batch.
Who to make them for
- A knitter: the row counter and the needle gauge as a pair.
- A dressmaker or quilter: the sewing gauge, with their name.
- Knitting groups and sewing classes: one each, with the group's name or each member's.
Selling them
Craft fairs, yarn shops and haberdashers are the natural places to offer these, plain or with a name. A group's counter can carry the group's name, such as RIVERSIDE KNITTERS, and a shop can give its own-name gauges with a purchase.
For a class or a group, paste the names one per line into a bulk order and each piece comes out with its own name. Bulk orders and the right to sell come with the Seller plan. For more small presents at this time of year, see the Christmas stocking fillers page.
Planning what to make next? Browse personalised print ideas by occasion, or work out prices, party orders and colour changes with the free maker tools.