A custom initiative tracker to 3D print, and more table gear for role-playing groups

A Christmas present for the friend who runs the game: a turn order rail with a tile for every hero and monster, the group's name along the top. With it, a card holder and a two-player scoreboard for the rest of the table, and how to print and sell all three.

A custom initiative tracker to 3D print, and more table gear for role-playing groups

What to know first

In a tabletop role-playing game, the game master runs the session: they set up the adventure, play the monsters and other characters, and referee the rules. One of the jobs that falls to them in every fight is keeping track of whose turn it is. Most games use an initiative system for this: in games such as Dungeons & Dragons, each character gets an initiative number from a stat plus a dice roll, and everyone acts in that order. Some games set the order once per fight, others every round.

Groups track it in different ways: a list on paper, cards clipped to the GM's screen, or a tracker the whole table can see. A tracker everyone can read saves the GM from calling names and lets players get ready before their turn. It needs a slot per place, a tile per character that can move, and room for monsters.

That makes the person who runs the game a natural place to start when buying for a gaming group, with a couple of pieces for everyone else.

A custom initiative tracker for the table

The turn order tracker is a rail with four to eight numbered places and a tile for every character. The heroes' tiles carry their names, typed in as a list, and there are up to eight numbered monster tiles. Each tile drops into a shallow pocket on the rail and lifts out to move. The group's name, or the adventure's, runs along the top: TURN ORDER by default, or THE RIVERSIDE FIVE for a group that has given itself a name.

When the order is decided at the start of a fight, each character's tile goes into the place it earned and play runs from 1 upwards. When a character leaves the fight, its tile comes out and the rest close up. For a fight with more than eight in it, one tile can stand for a group of monsters that act together, or a second rail goes alongside.

It is tied to no game. It tracks an order of turns and carries no game's name or artwork, so it works for any tabletop adventure, and for board games where the turn order changes. The rail is 160 to 245 mm long, and the lettering can be pixel letters for a group that likes that look.

Cards in a rack

Plenty of tabletop adventures use cards: spells, items, a hand dealt to each player. The playing card holder is a rack that holds a hand upright with the player's name along the front. It has one slot or two, leaning back up to 20 degrees, and you set the slot's width: about 1.8 mm for plain cards, about 3 mm for sleeved cards. Short and with one slot, it becomes a stand for a single card, which is a good place to keep a character's portrait or the card everyone keeps asking to see.

At the standard 200 mm, each slot holds a fan of about fifteen overlapped cards. One per player, each with their character's name, is a set for the whole group. Playing card holders for kids and grandparents covers the same rack for family card games.

A score for two

For the nights when the group plays something shorter, the scoreboard with sliding pointers keeps score for two players or two teams: a name over each of two scales and a pointer under each that slides to the score. It plays to 5, 7, 10, 11, 15 or 21. The pointers run in dovetailed channels and are shut in by end caps, so they can't be lost in the box. It leans on two feet or hangs on the wall.

Printing them

The tracker needs three filaments on an ordinary printer. The rail prints face up with one filament change when the numbers start, and the pockets are cut into its face, so no supports are needed. The tiles go on a plate of their own with a change for the names. Print the monster tiles again in another colour if you want them to stand out from the heroes. If a tile is tight in its pocket, raise the fit setting and reprint the rail.

The scoreboard is also three filaments: the board with one change for the names and numbers, and the pointers and caps on their own in a third colour. The card holder prints the way it stands, with a change for the name's last few layers. None of them need supports or a multi-colour printer.

Selling to groups

Ask for the group's name, each character's name and how many monster tiles. Characters change between adventures, so the tiles are a repeat order: a new campaign means a new set. A games club or café that runs regular tables may want a rail per table.

For card holders, one per player, paste the names one per line into a bulk order. Bulk orders and the right to sell come with the Seller plan. The games and family game nights page has more for the same table.

Planning what to make next? Browse personalised print ideas by occasion, or work out prices, party orders and colour changes with the free maker tools.

Take your next custom order in minutes

Type your customer's text, send them a picture to approve, download a print-ready file.

Start selling

Keep reading