# Personalised name puzzles for toddlers: how to 3D print and sell them

> A personalised name puzzle is a first-birthday classic. How to 3D print a custom name puzzle for toddlers in four colours, keep it safe for small hands, fit long names, and price and pack the orders.

Web page: https://stlmint.app/blog/personalised-name-puzzles-to-3d-print

By Neha Parsiya (https://stlmint.app/authors/neha-parsiya). Published 2026-10-15, updated 2026-11-18

A personalised name puzzle is a board with a child's name cut into it. Each letter lifts out, and each one only goes back in its own place. It is given as a first-birthday present, a baby shower gift or a nursery shelf piece.

## What to know first

- **It is a toy, so toy rules apply.** In Great Britain toys fall under the [Toys (Safety) Regulations 2011](https://www.gov.uk/government/publications/toys-safety-regulations-2011/toys-safety-regulations-2011-great-britain) and need a UKCA or CE mark. Trading Standards' [quick guide to toy safety](https://www.businesscompanion.info/en/quick-guides/product-safety/toys) lists the EN 71 series of standards behind them, starting with Part 1 on mechanical and physical properties. In the US, the [small parts rule (16 CFR 1501)](https://www.ecfr.gov/current/title-16/chapter-II/subchapter-C/part-1501) sets the test for choking hazards in toys meant for children under 3. In India, toys need BIS certification.
- **Size the pieces for the youngest user.** Chunky, rounded letters that stand proud of the board are easier for small hands to lift, and bigger pieces are further from the small-parts limit.
- **Colour should be in the material.** The classic wooden version is cut, sanded and painted. A printed one carries its colour in the filament, so there is no paint to chip.

The rest of this post covers our design, how to print it and how to sell it.

## What the name puzzle design makes

The [name puzzle](/designs/name-puzzle) turns a child's name into chunky, rounded capital letters that sit in letter-shaped pockets in a board.

- **Letters** are 7 mm thick with rounded corners and a soft rounded top edge. The pockets are 4 mm deep, so each letter stands 3 mm proud for small fingers to grab.
- **Closed letters** like A, B, O and R keep their middles. The board has a matching post in each pocket that the letter drops over.
- **An extra piece** goes after the name: a star, heart, flower or cat. You can put it at both ends, and the cat has its face pressed into the top.
- **Fit**: every piece is 0.4 mm smaller than its pocket all round, and each pocket has a small chamfer round its mouth, so pieces find their way in.

Names are always made capitals, so every letter is one solid piece. Stick to A to Z and numbers; accented letters would come out as more than one piece. A name can be up to 12 letters.

## Sizes: how big is a name puzzle?

The board is 220 mm wide at most by default. A four-letter name with a star makes a board 220 mm long and 60 mm tall, with letters about 35 mm tall. Shorter names get bigger letters, up to the letter height you set (50 mm by default, adjustable from 30 to 70 mm); longer names get smaller letters so the board stays within its width.

The maximum board width can be set from 120 to 250 mm, to suit your printer or a smaller, cheaper version.

### Long names on two rows

When one row would make the letters smaller than 30 mm, the name moves onto two rows by itself. If the name has a space, the break goes there, so "ANA SOFIA" splits into its two names; otherwise it breaks in the middle. You can also force one or two rows.

A name still too long at 18 mm letters will not build: make the board wider or use a shorter form of the name.

## Is a 3D printed name puzzle safe for toddlers?

The design is made for small hands: big, thick pieces, rounded corners, rounded top edges and a small chamfer under each piece so the first layer leaves no sharp lip. Still, a 3D print is only as safe as the print itself, so:

- **Check every piece.** Run a finger round each letter and the board, and trim any strings or blobs before packing.
- **Mind the narrow letters.** An I, a J or a 1 at small sizes is a slim piece. Keep letters large (a shorter name, a wider board, or two rows) for the youngest children.
- **Give an age guide.** Pieces this size are not something to leave with a baby who puts everything in their mouth. Label the puzzle for supervised play and state an age on the listing, such as 3 years and up, and present it as a keepsake for younger children.
- **Use plain filament.** PLA, or PETG if it will be thrown about. No paint, glitter or varnish.
- **Know the rules where you sell.** If you sell it as a toy, toy safety rules apply: BIS certification in India, and CE or UKCA marking against EN 71 in Europe and the UK. Check what applies to you before listing it as a toy.

A short card in the box ("Supervise young children. Not for chewing.") shows parents you have thought about it.

## Printing the four colours

The board is one colour (the base part). The letters take turns through four colour parts, l1 to l4, so no two neighbouring letters match. Four small dots in the board's corners show the colour set, one dot per letter colour.

You have two ways to print it.

**With an AMS.** Open the Bambu Studio project, assign the board and four letter parts to five filament slots, and print it all on one plate. Easy, but every layer of the letters changes colour up to four times, so it purges a lot of filament.

**One colour per plate.** The board and the letters are separate flat pieces, so you can print them as separate jobs: the board in white or a pale colour, then all the l1 letters in red, the l2 letters in yellow, and so on. Download one STL per part from the studio. This needs no AMS at all, just a filament swap between plates, and it wastes almost nothing. The corner dots sit in the board, so they need the multi-colour route: turn **corner dots** off for this method. They stay on for a name of fewer than four pieces, so keep the star or another motif on short names.

Everything prints flat, face up, with no supports. If you are new to colour parts, our guide to [two-colour name prints in Bambu Studio](/blog/two-colour-name-prints-in-bambu-studio) explains the 3MF and per-part downloads.

### Test the fit first

Print one letter and try it in the board before a whole set. If it is tight, raise the clearance to 0.5 or 0.6 mm and keep that setting for later orders.

### Bed size

In the print layout the letters sit below the board, in the board's order, which also makes packing easy. A one-row board with its letters needs roughly 220 by 105 mm, so it fits a 256 mm bed comfortably. On a 220 mm bed set the board a little narrower, around 200 mm. On a 180 mm bed, set the board to about 170 mm, or print the board and the letters on separate plates. A two-row board is taller, so the letters may need a plate of their own.

## Colour sets to offer

Offer two or three sets: bright (white board with red, yellow, blue and green letters), pastel (cream with pink, mint, lilac and pale yellow), or one colour for a nursery with a set scheme. Hearts at both ends make a nice first-birthday version.

## Photos and packaging

Shoot the puzzle assembled from above, then with two or three letters lifted out beside it, so buyers see the pieces come out. Our post on how to [photograph 3D prints with your phone](/blog/photograph-3d-prints-with-your-phone) covers light and backgrounds.

Pack it assembled, in a flat box with a snug card insert so the letters cannot fall out in transit. Add the safety card and a gift note if asked. More on boxes and posting in [packing and posting small 3D prints](/blog/packing-and-posting-small-3d-prints).

## Taking orders and getting the name right

Ask for the name typed exactly as it should appear, the colour set and the motif, then send a picture from the studio and wait for an "approved". See [avoiding misspelled names](/blog/avoid-misspelled-names-on-custom-orders).

Nurseries and playschools sometimes order one per child at the start of the year. Collect the names as one list, one per line, and on the Seller plan paste it into **Bulk order** on the design to get one file per name.

## Pricing and lead times

A name puzzle uses far more filament and printer time than a keychain, plus five colours and careful checking, so price it as a gift, not a trinket. Work out filament, machine time and your own time per puzzle, then add margin; [how to price personalised 3D prints](/blog/how-to-price-personalised-3d-prints) walks through it. Charge a little more for long names on two rows and for a motif at both ends.

Quote two or three days for a single order and a week for class sets, and ask birthday buyers for the party date.

## Add-ons that go with it

Pair it with a [kids' door plaque](/designs/kids-door-plaque): the same name on a rocket, rainbow, dinosaur, crown, castle or whale, about 200 mm wide, for the bedroom door. Sell the two as a first-birthday set. For more matching gifts, see the [new baby gifts ideas](/ideas/new-baby-gifts). For a party bag, the [surprise name stencil](/designs/surprise-name-stencil) hides the child's name in outline letters until the last stop.
