# Controller wall hook with a name

> A plate for the wall by the console with a name on it and two prongs a controller hangs on. The prongs lean up towards the wall and widen at the tip, so it can't slide off. One controller, two one above the other, or a headset on a wide prong.

Web page: https://stlmint.app/designs/controller-wall-hook

Personalise it in the studio: https://stlmint.app/app?p=controller-wall-hook

## Details

- Category: [Desk accessories](https://stlmint.app/designs/desk-accessories.md)
- Price: $4 for a single file, or included in every pass and plan (Party pass $8 for 7 days, Season pass $20 for 90 days, Seller plan $12 per month, Seller year pass $99 for a year; see [pricing](https://stlmint.app/pricing.md))
- Size: About 110 × 114 × 54 mm (11.0 × 11.4 cm) with the example text
- You type: Name, Holds, Fixing, Lettering, plus 6 more options for fine-tuning
- Colours: 2 parts (base, text), so it prints in 2 colours or as one
- Files: STL for any slicer, plus a two-colour Bambu Studio project
- Printing: Clad (2 colours, 1 filament swap): Colours stacked in layers, like a clad coin: pause and swap filament where each colour starts. No AMS needed. One Strike (one piece): Comes off the plate ready to use, with nothing to put together.

## Why sellers like it

- Two prongs a controller rests across, leaning up 12 degrees with a flared tip
- One controller, two one above the other, or a headset on a single wide prong
- The name sits high on the plate, so it shows over the controller
- Two screws the controller hides, or mounting tape
- Prongs 35 to 70 mm long and 40 to 80 mm apart, to suit the controller
- One piece, printed flat on its back with no supports; the prongs come out in the name's colour

## Good for

- Console corners
- Shared living rooms
- Children's rooms
- Streaming desks
- Gifts for gamers

## A place on the wall

A controller on the sofa gets sat on, and one on the floor gets trodden on or chewed. This plate goes on the wall by the console and the controller hangs on it, across two prongs that lean up towards the wall and widen at the tip.

The name sits high on the plate, clear of the controller, so everyone knows whose it is.

## One, two, or a headset

- **One controller**: a plate about 110 mm square.
- **Two controllers**: one above the other on a taller plate, for a shared console.
- **A headset**: a single wide prong that spreads the headband.

## Printing tips

- Print it flat on its back, prongs up, with no supports.
- One filament change when the plate is finished; the name and the prongs print in the second colour.
- The Bambu 3MF prints it at the sturdy setting: four walls and 25% gyroid infill. Use the same for an STL.

## Selling tips

Sell it with the buyer's name or gamer tag, in the console's colours. A desk version is the [sunset controller stand](/designs/sunset-controller-stand), and the [headphone stand](/designs/headphone-stand) is its partner for a headset that lives on the desk.

## Questions about the controller wall hook

### Which controllers does it fit?

Any that can rest across two prongs, which is nearly all of them: the controller sits with its body on the prongs and its grips hanging either side or below. Set the gap between the prongs (40 to 80 mm) and how far they stand out (35 to 70 mm) to suit yours.

### Why are the prongs the same colour as the name?

The plate prints first in one colour, and everything above it prints in the second: the name and the prongs. That way no layer mixes two colours and any printer can make it with one filament change.

### Is it strong enough?

Yes, for a controller or a headset. Each prong is 13 mm across with a wider root, and the Bambu 3MF prints it at the sturdy setting (four walls, 25% gyroid infill), which makes the prongs nearly solid. For an STL use the same. It is not a coat hook: don't hang bags on it.

### Screws or tape?

Two screws hold best and sit behind the controller. Strong double-sided mounting tape works on a smooth, clean wall for a single controller; press the plate on for a minute and leave it a day before loading it.

### How does it print?

Flat on its back with the prongs standing up, with no supports: the prongs lean only 12 degrees and the tips flare at 45. Change filament once when the plate is done.

### Can I sell it?

Yes, on the Seller plan. Offer it with the buyer's name and in pairs for a shared console.

## Ideas for selling it

- [Gifts for gamers to 3D print and sell: name signs, a turn order tracker and a headphone stand](https://stlmint.app/ideas/gifts-for-gamers.md)

## Sellers also offer

- [Sunset Controller Stand](https://stlmint.app/designs/sunset-controller-stand.md): A controller stand with a sunset behind it: a striped sun with two palms against it, a rail across the front with the player's name, and two side rails the controller rests on. Four flat pieces that slot together. ($5 a file, 3 colours)
- [Headphone Stand](https://stlmint.app/designs/headphone-stand.md): A weighted foot with the name, an upright post and a wide domed cradle. ($6 a file, 2 colours)
- [Now Playing Case Stand](https://stlmint.app/designs/now-playing-case-stand.md): A stand for the game being played right now: the case leans in a slot cut to its thickness, and NOW PLAYING is raised on the block in front with a name under it. Holds up to three. ($4 a file, 2 colours)
