# Flat-pack laptop stand with a name

> A laptop stand in two flat pieces that slot together into a cross: the laptop sits on their four sloping arms, raised off the desk and tilted towards you, with the owner's name on both pieces.

Web page: https://stlmint.app/designs/cross-laptop-stand

Personalise it in the studio: https://stlmint.app/app?p=cross-laptop-stand

## Details

- Category: [Desk accessories](https://stlmint.app/designs/desk-accessories.md)
- Price: $5 for a single file, or included in every pass and plan (Party pass $8 for 7 days, Season pass $20 for 90 days, Seller plan $12 per month, Seller year pass $99 for a year; see [pricing](https://stlmint.app/pricing.md))
- Size: About 173 × 173 × 70 mm (17.3 × 17.3 cm) with the example text
- You type: Name, Length, Back height, Front height, plus 5 more options for fine-tuning
- Colours: 2 parts (base, text), so it prints in 2 colours or as one
- Files: STL for any slicer, plus a two-colour Bambu Studio project
- Printing: Clad (2 colours, 1 filament swap): Colours stacked in layers, like a clad coin: pause and swap filament where each colour starts. No AMS needed. Mint Set (2 pieces on 1 plate): Prints as pieces that slot or press together; the studio shows it assembled.

## Why sellers like it

- Two flat pieces, no screws, no glue
- Lifts the back 45 to 95 mm; you set the slope
- A lip at each front end stops the laptop sliding
- The name on both pieces
- Comes apart and lies flat in a laptop bag
- Prints flat, no supports

## Good for

- Working from the kitchen table
- Students
- Hot desks and shared offices
- Video calls: a camera at eye level
- Presents for new starters
- Tablets and drawing pads

## A desk in a bag

People who work at a different table each day carry a laptop and wish they had a stand. Two flat pieces in the bag's back pocket are one, and with a name on them they come back from a shared desk.

## Printing tips

- Print both pieces flat, in PETG, and change filament for the name.
- Four walls matter more than infill for stiffness.
- If the cross is loose or tight, change the slot clearance and reprint one piece.

## Selling tips

Sell to offices by the team, each with a name, and say plainly in the listing that it should be printed in PETG.

## Questions about the cross laptop stand

### How does it go together?

Each piece has a slot half way along: one from the top, one from the foot. Slide one into the other at right angles and they make a cross. The laptop rests on the four arms.

### Which filament should I use?

PETG, or ASA. A laptop's underside gets warm, and PLA softens with heat over time and under load. Print with four walls and at least 30 per cent infill.

### What size laptop does it take?

At 240 mm long the arms reach the corners of most 13 to 16 inch laptops. Check that your laptop's feet or vents don't land on an arm, and that it sits steadily, before you leave it.

### Is it strong enough?

It is two plates on edge, which is a stiff way to use plastic, and it is meant for a laptop's weight and nothing more. Don't lean on it. If the slots are loose, lower the clearance and reprint one piece.

### Can I sell these?

Yes, on the Seller plan. Offices order them with each person's name.

## Ideas for selling it

- [Back-to-school name tags to 3D print and sell](https://stlmint.app/ideas/back-to-school.md)
- [Desk name plates and office signs to 3D print and sell](https://stlmint.app/ideas/offices-and-coworking.md)

## Sellers also offer

- [Name Phone Stand](https://stlmint.app/designs/name-phone-stand.md): A leaning desk stand that holds the phone up for video calls, with a name or company name on the panel below it. Three flat pieces that slot together. ($4 a file, 2 colours)
- [Headphone Stand](https://stlmint.app/designs/headphone-stand.md): A weighted foot with the name, an upright post and a wide domed cradle. ($6 a file, 2 colours)
- [Desk Name Plate](https://stlmint.app/designs/desk-name-plate.md): The name across the front of a desk organiser with a pen cup, tray and card slot. ($5 a file, 2 colours)
