Digital 3D print fileDownloads as STL3MF
Cross stitch bookmark blank with a name, to 3D print
A bookmark to cross-stitch: a printed plastic-canvas grid inside a finished rim, with a name on the band at the foot, a hole for a tassel and arrows at the middle row so a chart is easy to count on.
- Clad 2 colours, 1 filament swapColours stacked in layers, like a clad coin: pause and swap filament where each colour starts. No AMS needed.
- One Strike One pieceComes off the plate ready to use, with nothing to put together.
What you download
cross-stitch-bookmark-EMMA.stlFor any slicer and any 3D printercross-stitch-bookmark-EMMA.3mfA Bambu Studio project with the colours set
Digital files only. Nothing is posted: you print it yourself, for you or for your customers.
Single files and the Party pass and Season pass are for personal use and gifts. To sell prints you need an active Seller plan or Seller year pass; prints made while it is active stay yours to sell after it ends. The digital files themselves may never be shared or sold. Read the licence
- Size
- About 46 × 160 × 2 mm (4.6 × 16.0 cm) with the example text
- You type
- Name, Grid, Top, Lettering, plus 5 more options for fine-tuning
- Colours
- 2 parts (base, text), so it prints in 2 colours or as one
- Files
- STL for any slicer, plus a two-colour Bambu Studio project
Why sellers like it
- A grid of square holes like plastic canvas, inside a solid rim that needs no edging
- 10-count for embroidery floss or 7-count for wool and thick yarn
- A name or a title raised on the band at the foot
- Arrows on the rim at the middle row, and ticks every ten rows
- Arched, pointed or square top with a hole for a tassel
- One flat piece, no supports, one filament change
A bookmark to stitch, not to cut out
Plastic canvas from a craft shop is a flat sheet: to make a bookmark from it you count out a rectangle, cut it, and then oversew the rough edge before you can start. This one comes off the printer already a bookmark, with a smooth rim, a rounded foot, a hole for the tassel and the owner's name on the band. All that's left is the stitching.
Easy to count onto
Cross-stitch charts mark the middle and every tenth square. So does this: arrows on both sides of the rim point at the middle row, and small ticks mark every ten rows up and down from there. Start your motif in the middle and it ends up in the middle.
Floss or yarn
10-count has small holes for embroidery floss and fine detail: a flower, a name, a border of hearts. 7-count has bigger holes for wool and thick yarn, quicker to fill and right for children who are starting out.
Printing tips
- Print flat, with no supports.
- Slow the first layer down so every bar of the grid sticks.
- A pale bookmark (cream, white or light grey) shows the stitching best; the name in a darker colour.
Selling tips
Sell it as a kit: the bookmark, a few colours of floss, a tapestry needle and a printed chart. A set of bookmarks with every child's name makes a craft club afternoon, and for winter there is a cross stitch ornament to go with it.
Questions about the cross stitch bookmark
What can I stitch on it?
Anything from a cross-stitch chart, the same way as on plastic canvas: each stitch crosses one square of the grid. Use a blunt tapestry needle. 10-count takes four to six strands of embroidery floss; 7-count takes wool, thick yarn or a full skein of floss.
How big is the grid?
At the default 50 mm width and 160 mm length, 10-count gives 15 holes across and 45 rows below the top, 7-count 11 across and 31 rows, with more in the shaped top. The width is rounded down to whole holes, so the rim's inside edge always falls on a bar. Length runs from 120 to 200 mm.
What are the arrows and ticks for?
As on a printed chart, the arrows point at the middle row, so you can start a motif in the middle and count out. The ticks mark every ten rows from there. Turn marks off for a plain rim, or keep only the arrows.
Will the holes print cleanly?
Yes, on a 0.4 mm nozzle. The bars between holes are 0.95 mm at 10-count and 1.25 mm at 7-count, two or three lines wide, and the holes go straight through, so there's nothing to bridge. Print the first layer slowly so every bar sticks.
How do I finish the back?
Glue a strip of felt over the back once the stitching is done, or leave it if the back is neat. A tassel or a ribbon goes through the hole at the top.
How does it print?
Flat, with no supports. Change filament once where the name and the marks begin. The bookmark is 1.6 mm thick by default; thinner bends, thicker makes stitches pull hard.
Can I sell it?
Yes, on the Seller plan. Sell the blank on its own with the buyer's name, as a kit with floss, a needle and a chart, or as a set for a class or a craft club.
Ideas for selling it
More in personalised print ideas by occasion. Pricing an order? Try the profit calculator and the other free maker tools.
Sellers also offer
Start selling the cross stitch bookmark
Type your customer's text, send them the picture, download the print file.
Early Black Fridaythrough Nov 30 (US Pacific time)
The Seller plan at $12 $6 a month
For your first 3 months, then $12. Every design, bulk lists, and the right to sell your prints. Comes off at checkout, no code needed.