# Logo click slider: a sliding fidget clicker with your logo

> A tile with your logo on it that slides along a track and clicks into every stop, with a name or website on the frame. Upload any logo. Prints in place in one go, with no magnets or springs to buy.

Web page: https://stlmint.app/designs/logo-click-slider

Personalise it in the studio: https://stlmint.app/app?p=logo-click-slider

## Details

- Category: [Fidget clickers](https://stlmint.app/designs/fidget-clickers.md)
- Price: $4 for a single file, or included in every pass and plan (Party pass $8 for 7 days, Season pass $20 for 90 days, Seller plan $12 per month, Seller year pass $99 for a year; see [pricing](https://stlmint.app/pricing.md))
- Size: About 53 × 36 × 6 mm (5.3 × 3.6 cm) with the example text
- You type: Your logo, Words on the frame, Stops, Click, plus 7 more options for fine-tuning
- Colours: 2 parts (base, text), so it prints in 2 colours or as one
- Files: STL for any slicer, plus a two-colour Bambu Studio project
- Printing: Clad (2 colours, 1 filament swap): Colours stacked in layers, like a clad coin: pause and swap filament where each colour starts. No AMS needed. One Strike (one piece): Comes off the plate ready to use, with nothing to put together.

## Why sellers like it

- Upload any logo: PNG, JPG or SVG
- Clicks into every stop, back and forth
- Prints in place: the tile comes off the bed already in its track
- No magnet, spring or switch to buy
- Three to eight stops; soft, firm or hard clicks
- Your name or website along the frame

## Good for

- Company merch and giveaways
- Gym and club keyrings
- Conference swag
- Desk fidgets
- Team gifts
- Shop counter impulse buys

## A logo that slides and clicks

Fidget sliders are the ones people flick back and forth without looking. This one carries a logo on the tile, under the thumb, and the name on the frame. Push the tile along and it drops into each stop with a tick, then back again.

## How it works

- The tile's long edges are a V that sits in matching grooves, so it slides but can't lift out.
- A spring tongue cut in the frame pushes a tooth into notches along the tile's top edge, one notch for each stop.
- Your logo stands up on the tile inside a raised border; the name, website or slogan runs along the frame below.

## Printing tips

- Print it flat as it comes, with no supports: the tile prints in place in its track.
- Change filament where the logo and words begin (0.8 mm under the top).
- If the first layer spreads, the tile can stick to the frame: lower the bed temperature a little or raise the fit.
- Thin lines in a busy logo print better with the logo's lines thickened a little (All options).

## Selling tips

Ask the customer for their logo as a PNG or SVG and the words for the frame. Wide logos suit the tile better than tall ones. For a round logo, offer the [click dial](/designs/logo-click-dial) instead.

## Questions about the logo click slider

### What logo can I use?

Any picture of it: a PNG, JPG, WebP or SVG. A logo on a plain white or see-through background works best. The studio reads it in your browser, splits it into dark and light, and shows the shape that will print; tick “Light logo on dark background” for a white logo on a coloured square. Photos and soft shadows don't work.

### How does it click without a magnet?

A thin tongue is cut in the frame above the track, with a small tooth on its end. The tooth drops into a row of notches along the tile's edge, so sliding the tile pushes the tongue aside and lets it snap back: a tick at every stop. Nothing to buy and nothing to put together.

### How does it print in place?

Flat on the bed, no supports. The tile's long edges are a V and the frame has matching grooves, both at 45 degrees, so they print without supports and the tile can't lift out. There is a small gap all round; if the tile comes off the bed stuck, push it firmly from one end, and if it stays stuck raise the fit in All options and reprint.

### How many colours does it need?

Two, stacked. The frame and tile print in one colour and the logo and words stand on top in the second, so one filament change does it on any printer.

### How big is it?

About 53 x 36 mm and 5.8 mm thick with five stops, plus the key ring loop. More stops make the track longer; the tile width sets the height.

### Can I sell these with my customers' logos?

Yes, on the Seller plan. Only put a logo on a clicker when the customer owns it or has permission to use it.

## Sellers also offer

- [Logo Click Dial](https://stlmint.app/designs/logo-click-dial.md): A coin with your logo on it that clicks as it turns in its ring, with your name round the edge. Prints in place, no metal parts. ($4 a file, 2 colours)
- [Logo Push Clicker](https://stlmint.app/designs/logo-push-clicker.md): Press the logo and it clicks down, let go and it clicks back: a button with a printed spring, your name on the body. Prints in place in one piece. ($4 a file, 2 colours)
- [Logo Clicker Business Card](https://stlmint.app/designs/logo-clicker-business-card.md): A business card people keep: a coin with your logo clicks as it turns in the card, with your name, title and contact details beside it. ($5 a file, 2 colours)
