Digital 3D print fileDownloads as STL3MF
Wedding table number stake for centrepieces
A table number on a stiff stake that pushes into the flowers, the florist's foam or a potted plant, in an arch, a leaf wreath, a hexagon or a scooped card, with the couple's initials underneath.
- Clad 2 colours, 1 filament swapColours stacked in layers, like a clad coin: pause and swap filament where each colour starts. No AMS needed.
- One Strike One pieceComes off the plate ready to use, with nothing to put together.
What you download
table-number-stake-7.stlFor any slicer and any 3D printertable-number-stake-7.3mfA Bambu Studio project with the colours set
Digital files only. Nothing is posted: you print it yourself, for you or for your customers.
Single files and the Party pass and Season pass are for personal use and gifts. To sell prints you need an active Seller plan or Seller year pass; prints made while it is active stay yours to sell after it ends. The digital files themselves may never be shared or sold. Read the licence
- Size
- About 80 × 220 × 4 mm (8.0 × 22.0 cm) with the example text
- You type
- Table number or name, Couple's initials, Frame, plus 15 more options for fine-tuning
- Colours
- 2 parts (base, text), so it prints in 2 colours or as one
- Files
- STL for any slicer, plus a two-colour Bambu Studio project
Why sellers like it
- Four frames: a tall arch, a round leaf wreath, a hexagon and a card with scooped corners, each with a fine double line
- The number in a big script or a tall bold face, or a table name such as Jasmine or Family
- The couple's initials at the bottom over a small diamond, heart or leaf sprig
- A wide stake with a raised spine and a point, so it goes into foam or soil without bending
- 80 mm wide and about 220 mm tall with the stake; the stake length is adjustable
- On the Seller plan, one table per line in a bulk order makes the whole set, 1 to 50
A number that stands up out of the flowers
A table number in the centrepiece is easier to spot from the door than one lying flat on the cloth, and it doesn't crowd the plates. This one is a card on a long stake. The florist pushes it into the foam, or the planner pushes it into a potted plant or a jar of moss, and it stands just above the flowers.
The card comes in four frames. The arch is a tall window with a round top. The wreath is a circle with two leafy branches climbing its sides. The hexagon suits a modern table, and the rounded card has the scooped inner corners of a printed invitation. Each has a fine double line inside its edge. The number sits in the middle with a small TABLE over it, and the couple's initials sit at the bottom over a little diamond, heart or leaf sprig.
The stake is wide and has a raised spine down its face, so it goes into firm foam without bending, and it ends in a point.
Printing tips
- Print face up, flat on the bed, with no supports. The whole stake fits diagonally on a 220 mm bed.
- Change filament at the top of the card (3 mm) for the lettering colour; the spine down the stake comes out in it too. That is the only change, so no AMS is needed.
- Use PETG for arrangements that stay in wet foam; PLA for dry ones.
- Dancing Script, Lobster and Pacifico give a script number; Big Shoulders and Saira Condensed give a tall bold one that reads from further away.
Selling tips
Sell the table numbers as a set with the place card holders and the seating chart pegs, all in the same colours. Florists and decorators are good customers too: they build centrepieces for many weddings and reuse a stock of numbered stakes, so offer them a plain set of 1 to 30 without initials.
Questions about the table number stake
What does the stake go into?
Florist's foam, the soil of a potted plant, sand or moss in a jar, or between the stems of a tight bouquet in a vase. Push in most of the stake so the card stands just above the flowers. For a vase of loose stems, wedge it against the side so it does not turn.
Will it bend or snap?
The stake is 7 mm wide and 3 mm thick with a raised spine down its face, and the corners where it meets the card are filled in, so it stays straight in foam and soil. Print it in PETG if it will sit in wet foam all day; PLA is fine for dry arrangements.
Can I use table names instead of numbers?
Yes. Type the name in the number box and leave the small TABLE line empty. Names shrink to fit the frame, so a short name like Jasmine or Family prints biggest. For long names, widen the card in All options.
How do I make a full set of table numbers?
On the Seller plan, paste the numbers one per line into a bulk order, 1 to 30 or however many tables there are. You get a ZIP with one file per table, all in the same frame and colours.
Which colours look best?
Ivory, white or blush for the card with gold, champagne or black lettering. Change filament at the top of the card for the lettering, frame lines, wreath and the spine down the stake.
Ideas for selling it
More in personalised print ideas by occasion. Pricing an order? Try the profit calculator and the other free maker tools.
Sellers also offer
Start selling the table number stake
Type your customer's text, send them the picture, download the print file.
Early Black Fridaythrough Nov 30 (US Pacific time)
The Seller plan at $12 $6 a month
For your first 3 months, then $12. Every design, bulk lists, and the right to sell your prints. Comes off at checkout, no code needed.