A Christmas Eve treat board for Santa: milk, cookies and a carrot, with the children's names

A Santa treat board with a ring for the glass of milk, a ring for the plate of cookies, a carrot for the reindeer and the children's names along the bottom. What goes on it, how big it is, and how it fits into a Christmas Eve box with a stop sign and a magic key.

A Christmas Eve treat board for Santa: milk, cookies and a carrot, with the children's names

What to know first

Leaving something out for Santa is one of the last jobs of Christmas Eve. What goes out depends on where you live: milk and cookies in the US, often a mince pie and a small sherry or beer in Britain and Ireland, and nearly everywhere a carrot for the reindeer. The half-eaten cookie and the empty glass in the morning are, as the Santa Claus article puts it, part of the "hard evidence" children are given. Many families make an evening of it: following the NORAD Tracks Santa map, which has run every Christmas Eve since 1955, then setting the treats out before bed.

Anything used for the treats has one rule: the food should sit on a real plate or in a glass. Prusa points out that the grooves between 3D-printed layers can hold bacteria and are almost impossible to clean, so a printed piece should be the place setting, not the plate.

A Santa treat board gives each treat its place: a ring for the glass, a bigger ring for the plate, a carrot for the reindeer, and the children's names along the bottom. Because it comes out again every year, it also suits a Christmas Eve box.

What the Santa treat board is

The Santa treat board is one flat board with FOR SANTA across the top. Under it are two rings, each with its word: MILK for the glass and COOKIES for the plate. Beside them is a carrot's outline with FOR RUDOLPH, and along the bottom runs a line such as WITH LOVE FROM LIAM & EMMA. There are small stars as well, which can be turned off.

Every word is yours to change. The second example on the design page leaves a mince pie and a beer instead, with the carrot turned off, which gives the two rings more room. Another example puts four grandchildren along the bottom on a 250 mm board, for a grandparents' house where everyone stays for Christmas.

The food goes on a plate

The rings are for a glass and a small plate, which sit inside them. Put the cookies on a plate or a napkin, not on the print itself: a 3D print has fine layer lines that are hard to clean. The board is the place setting, not the plate.

At the standard 220 mm width, the plate's ring is about 79 mm across and the glass's about 59 mm. That suits a saucer or side plate that overhangs the ring, and most tumblers. A wider board has bigger rings; the board goes from 170 to 250 mm.

Clean it with a damp cloth. Don't put it in a dishwasher: PLA softens in the heat.

A Christmas Eve box with a treat board, a sign and a key

The board is the centre of the evening, and two other designs make it a set with the same names on each.

  • The Santa stop here sign is a red octagon with SANTA, STOP and HERE, and the children's names on a banner under it. It goes on a stake in the lawn or a plant pot, on two feet on a windowsill, or on a ribbon on the door. Print it in PETG if it will be out in sun and frost.
  • Santa's magic key is for homes with no chimney: a big key with SANTA'S MAGIC KEY along the shaft, a star, a snowflake or a heart cut through the bow, and a tag with the family's name. It hangs on the outside of the front door on Christmas Eve and comes down on Christmas morning.
  • A stocking name tag for each child finishes the box.

There is a longer list in Christmas Eve box ideas to 3D print, and the Christmas decorations page has the rest of the season's designs.

Printing it

It prints as one flat piece, face up, with no supports. The words and rings are a second colour stacked on top of the board, so you change filament once when they start; no multi-colour printer is needed. Red with white, or dark green with white, both look right beside a tree. At 250 mm the board fills the bed's width, so check your printer's usable area first.

For sellers

The treat board is made to order with the children's names, and selling it needs the Seller plan. Set a last order date that leaves time for the post (for 2026, USPS recommends sending Ground Advantage by 17 December for delivery in the lower 48 states before Christmas), and offer it with the stop sign or the key as a Christmas Eve set.

Nurseries and childminders may want them too. When only the line of names changes from one board to the next, paste one per line into a bulk order, such as WITH LOVE FROM NOAH, and keep every other word the same. Bulk orders and the right to sell both come with the Seller plan.

Planning what to make next? Browse personalised print ideas by occasion, or work out prices, party orders and colour changes with the free maker tools.

Take your next custom order in minutes

Type your customer's text, send them a picture to approve, download a print-ready file.

Start selling

Keep reading