A pickup token system for a small café: tokens, a board and number tents

An order number system for a café made of three printed parts: numbered tokens the customer holds, a board behind the counter that shows which numbers are out, and tents for the tables when the food is carried over. How they fit together, how to print a set and how to sell one.

A pickup token system for a small café: tokens, a board and number tents

A small café that takes the order at the till and hands the food out later needs some way to join the two. The usual options are:

  • Calling names. Free, but it fails when there are two Emmas or the room is loud.
  • Printed receipt numbers. The slips get crumpled, thrown away or mixed up.
  • Electronic pagers. Restaurant pagers vibrate, flash or beep when an order is ready, but they cost far more per unit and need charging.
  • Reusable numbered tokens or table tents. Cheap and quiet, but they pass from hand to hand, so they need cleaning.

That last point matters for any food business. In the UK, the Food Standards guidance on gov.uk lists touch points such as door handles and electronic devices among the things a food business must clean regularly, and a token that goes from customer to counter all day is one of them. A smooth, wipeable token and a routine for wiping them helps.

A simple order number system for a café can be three printed things: pickup tokens for the customer, a board that keeps them, and number tents for the tables. The same parts work as pickup tokens for a restaurant, a canteen or a juice bar.

The token in the customer's hand

The pickup token is a numbered disc handed over with the order. The number fills the middle, big enough to read at arm's length, and the café's name runs round the bottom of a coin, or straight across a square token or a ticket with notched corners. The customer holds it while they wait, the counter calls the number, and the token comes back when the food goes out.

It is 40 mm across and 3 mm thick, with an 8 mm hole at the top. Size, thickness and the hole can all be changed, and the hole can be left out.

The board behind the counter

Tokens in a bowl tell nobody which numbers are with customers. The token board gives every token its own peg, with the token's number printed on the board behind it. A number you can read is an order that has not come back.

The standard board holds twenty 40 mm tokens, in 2 to 8 columns and 1 to 6 rows depending on the token size and the bed. It can start at any number, so a second board runs 21 to 40 next to the first. The pegs are flat strips printed lying down and pushed through slots from behind, with a hook at each tip, so there are no thin upright pins to snap off. Four screws and four spacers hold it to the wall, and the wall holds the strips in.

When the food goes to the table

Some cafés don't call numbers; they carry the tray out. For those, the order number tent is the better fit. The customer takes it to their seat, and the runner looks for the number, not the face. Two plates lean together under a ridge cap, so the number reads from both sides of the table, and the tent comes apart flat for the drawer. Each plate is 72 mm wide and stands about 85 mm high.

A café that does both, collection at the counter and table service at busy times, can run tokens and tents side by side with the same numbers.

Printing a set

Everything prints flat, face up, with no supports. The colours are stacked layers with one filament change, so no multi-colour printer is needed.

  • Tokens print a dozen to a plate, with the filament change where the numbers start. White numbers on a dark token, or black on yellow, read best. PETG stands up to daily wiping better than PLA; Prusa's food-safe printing guide notes that layer lines can trap dirt, so keep tokens out of the food itself and replace any that get grubby.
  • The board prints face up with a change when the numbers start; the peg strips and spacers go on a second plate in the board's colour. If the strips are tight or loose in their slots, change the clearance and reprint the board.
  • Tents have their plates and lettering in two colours, with the cap on a plate of its own. Print one test tent first and adjust the slot fit before printing a set of thirty.

Selling it to a café

On the Seller plan, paste the numbers one per line into a bulk order, 1 to 20 or 1 to 50, and you get one file per number. The café's name stays the same on every token. Bulk orders and the right to sell come with the Seller plan.

Sell it as a set, not single pieces: a board and twenty tokens in the café's colours, with a few spares. Tokens and tents go missing over time, which makes for a small repeat order; note which numbers are lost and reprint just those.

The cafés and restaurants page has the rest of what a counter needs, and 3D printed signs and tools for cafés has more for the same counter.

Planning what to make next? Browse personalised print ideas by occasion, or work out prices, party orders and colour changes with the free maker tools.

Take your next custom order in minutes

Type your customer's text, send them a picture to approve, download a print-ready file.

Start selling

Keep reading