Thanksgiving place cards to 3D print: pumpkins, acorns and leaves from one list of names
How to print Thanksgiving place cards for the whole table at once: type the guest list, get a pumpkin, an acorn or a leaf for every name, nine to a plate, each on a slot-on foot. Shapes, long names, colours and the feet, plus Friendsgiving table ideas.
US Thanksgiving falls on the fourth Thursday of November, fixed by a 1941 joint resolution signed by President Roosevelt, which puts it on 26 November in 2026. Friendsgiving, the meal with friends rather than family, is usually held on a separate day in the same season; Merriam-Webster dates the word itself to 2007. Both mean a host working out who sits where, often at a table stretched with extra chairs, and place cards settle that before anyone arrives.
Paper place cards usually go in the bin with the napkins. A printed pumpkin with a guest's name on it goes home in a pocket instead. These pumpkin place cards with names, and their acorn and leaf cousins, print for the whole table from one typed list, which also makes them an easy start to Friendsgiving table ideas. This is how to make a set.
One list of names
The harvest place cards take a single box of names. Type every guest with commas between them: Liam, Emma, Noah, Olivia, Ava, Grandma is the default. Each name gets its own card, and the cards lay themselves out nine to a plate, three by three, each with its foot under it.
A table of more than nine gets a second plate alongside, up to eighteen names in all. For a bigger gathering, split the guest list and make two sets.
Write the list in seating order and check spellings with the host before printing. A name that is wrong on a pumpkin can't be crossed out.
Pumpkins, acorns or leaves
There are three shapes:
- Pumpkins, the most familiar shape for Thanksgiving, and the only one for a Halloween dinner.
- Acorns, small and neat.
- Leaves, the most open shape, which suits a script name.
The default, "one of each by turns", goes pumpkin, acorn, leaf round the list, so neighbours at the table get different shapes. Or choose one shape for every card. The design page shows all pumpkins, and leaves in Lobster script.
Long names and card size
Every name on the table is set at one size, the size the hardest name to fit can take. That keeps the table even, but it means one long name, Christopher among Jo and Liam, makes all the others smaller too.
The fix is a bigger card. Cards are 56 to 76 mm across, 72 mm by default. If the list has a long name, go to 76 mm; if everyone is a Jo or an Ava, a smaller card is fine.
The feet
Each card has a notch in its lower edge, and a small foot slots on at a right angle. Push it on from below until it stops. It holds by friction, so the card stands by the plate and comes off again to go flat in a pocket.
Printers differ. If the feet are loose, or too tight to push on, change the slot clearance and print again. Print one card and its foot first if you are trying a new filament.
Colours
Orange with cream names for pumpkins. Brown, mustard or deep red for acorns and leaves. For a mixed table, print the same list three times in three colours and pick cards from each set, or print one plate in each colour for different parts of the table.
Each card is two colours in stacked layers. Print face up, flat on the bed, with no supports, and change filament where the names start; the shapes' lines come out in the name colour too. You don't need a multi-colour printer. The cards are thin and a plate of nine is a short print.
Friendsgiving table ideas
Friendsgiving tables are often a long run of borrowed chairs. Some ideas that use the same file:
- Cards double as a favour. Guests take theirs home, so they don't need a separate gift.
- Set a thankful turkey in the middle with FRIENDS, FOOD, HOME on its feathers, or one name per feather for a small group.
- For a meal spread over several tables, a table number stake pushes into a pot of flowers or a jar of moss in the centre of each. Its number box also takes a word, so tables can have names in place of numbers.
Selling place cards
Place cards are made to order from a guest list, so agree a date for the final names, and leave time for the post before 26 November. Sell by the table and price per card, and offer the turkey as a centrepiece for the same names.
Selling the prints needs the Seller plan, which gives you the right to sell them. If a venue or caterer wants table number stakes for every table, paste the numbers one per line into a bulk order, also on the Seller plan.
The same cards work after November for autumn weddings and harvest suppers; 3D printed wedding place cards covers the wedding side.
Planning what to make next? Browse personalised print ideas by occasion, or work out prices, party orders and colour changes with the free maker tools.