Digital 3D print fileDownloads as STL3MF
Furniture leg riser made to your leg's size
Lifts a sofa, bed, table or cabinet by its legs. Each leg stands in a pocket cut to its own size and shape, round, square or rectangular, even a splayed mid-century leg, and the riser adds as much height as you set. Tapered, fluted, plinth or plain.
- Fine One colourPrints in a single filament: any printer, no changes.
- One Strike One pieceComes off the plate ready to use, with nothing to put together.
What you download
furniture-leg-riser.stlFor any slicer and any 3D printerfurniture-leg-riser.3mfA Bambu Studio project with the colours set
Digital files only. Nothing is posted: you print it yourself, for you or for your customers.
Single files and the Party pass and Season pass are for personal use and gifts. To sell prints you need an active Seller plan or Seller year pass; prints made while it is active stay yours to sell after it ends. The digital files themselves may never be shared or sold. Read the licence
- Size
- About 76 × 76 × 80 mm (7.6 × 7.6 cm) with the example text
- You type
- Leg shape, Leg width, Leg depth (rectangle), Lift, Look, How many, plus 6 more options for fine-tuning
- Files
- STL for any slicer, plus a Bambu Studio project
Why sellers like it
- A pocket cut to the leg you measured: round, square or rectangular, 15 to 120 mm across
- Lifts from 10 to 150 mm, with the leg sitting 10 to 60 mm deep
- Splayed legs: the pocket leans up to 15 degrees with its floor kept level, and a notch shows which way
- Grip ribs inside squash as the leg goes in, for a snug fit without exact measuring
- Four looks: tapered with a wider foot, fluted, on a stepped plinth, or a plain block
- Prints standing, pocket up, in one colour; one, two or four on a plate
Lift it by the legs
Raising a sofa a few centimetres makes room for a robot vacuum or storage boxes. A higher bed is easier to get in and out of. A desk or a worktable at the right height saves your back. Shop risers come in a few sizes and rarely fit the leg; this one is made to it.
Measure the leg, pick how much to lift, and the pocket is cut to that leg: round, square or rectangular, with the corner rounding it has. The leg drops into the pocket and can't walk off the riser when someone sits down hard.
Splayed legs
Mid-century legs lean outwards, so a straight pocket would only touch them at one edge. Set the leg's angle and the pocket leans with it, while its floor stays level under the leg's flat foot. A notch in the rim shows which way to turn it.
Four looks
- Tapered: wider at the foot than the top, for a steady stance and a softer look.
- Fluted: rounded grooves up the sides, like a turned furniture foot.
- Stepped plinth: a wider tier at the bottom with a 45 degree shoulder.
- Plain block: straight sides, the most compact.
Printing tips
- Print it standing, pocket up, with no supports. The mouth of the pocket is chamfered so the leg finds its way in.
- The Bambu 3MF prints at the load setting: six walls, six top and bottom layers, 40% gyroid infill. Use the same for an STL.
- PETG for heavy furniture or warm rooms; PLA is fine for light tables and cabinets.
- Print one riser first and try it on the leg, then print the set.
Selling tips
Sell them in fours, made to the customer's leg size and lift, in a colour that matches the furniture: walnut brown, charcoal, oak beige or white. Offer leveller cups for tables that rock and caster cups for furniture on wheels.
Questions about the furniture leg riser
How do I measure the leg?
Measure across the leg where it touches the floor, not higher up: tapered legs are narrower at the foot. A round leg needs its diameter, a square leg its width, a rectangular leg its width and depth. Enter the leg's own size; the riser adds the clearance and the grip ribs itself.
My measurements are in inches.
Multiply by 25.4. A 1.5 inch leg is 38 mm, 1.75 inch is 44.5 mm, 2 inch is 51 mm. A 2 inch lift is 51 mm, 3 inch is 76 mm, 4 inch is 102 mm.
How tight is the fit?
With grip ribs on, the pocket is 0.4 mm bigger than the leg all round, and eight thin ribs stand 0.6 mm into that, so they squash a little as the leg goes in and hold it without rattling. If the leg won't go in, raise the clearance; if it's loose, lower it. Print one first as a test fit, then the set.
What about splayed legs?
Mid-century sofas and tables often have legs that lean outwards. Set how far the leg leans from upright (most are 5 to 15 degrees); the pocket leans the same way, its floor stays flat for the leg's cut foot, and a notch in the rim marks the side the leg leans towards. Turn each riser so the notch faces outwards, away from the furniture.
Is it strong enough?
It's made for it: the leg pushes straight down onto a solid floor under the pocket. The Bambu 3MF prints it at the load setting (six walls, six top and bottom layers, 40% gyroid infill); for an STL use the same. PETG suits anything heavy or in a warm room, since PLA can slowly sag under a constant load in heat. Check them now and then, as you would any riser.
Will it mark the floor?
Stick felt pads under each riser for wooden floors, or rubber pads to stop it sliding on tile.
Can I sell it?
Yes, on the Seller plan. Customers send their leg size and the lift they want, and each set is made to order.
Ideas for selling it
More in personalised print ideas by occasion. Pricing an order? Try the profit calculator and the other free maker tools.
Sellers also offer
Start selling the furniture leg riser
Type your customer's text, send them the picture, download the print file.
Early Black Fridaythrough Nov 30 (US Pacific time)
The Seller plan at $12 $6 a month
For your first 3 months, then $12. Every design, bulk lists, and the right to sell your prints. Comes off at checkout, no code needed.