Digital 3D print fileDownloads as STL3MF
Leg leveller cups for a wobbly table or cabinet
A set of low cups that stops a table, desk or cabinet rocking on an uneven floor. Each cup has its own lift for the gap under its leg, and carries its number, corner or lift on the side so the set goes back under the right legs.
- Fine One colourPrints in a single filament: any printer, no changes.
- One Strike 4 pieces, each ready to useComes off the plate ready to use, with nothing to put together.
What you download
leg-leveller-cups.stlFor any slicer and any 3D printerleg-leveller-cups.3mfA Bambu Studio project with the colours set
Digital files only. Nothing is posted: you print it yourself, for you or for your customers.
Single files and the Party pass and Season pass are for personal use and gifts. To sell prints you need an active Seller plan or Seller year pass; prints made while it is active stay yours to sell after it ends. The digital files themselves may never be shared or sold. Read the licence
- Size
- About 118 × 118 × 20 mm (11.8 × 11.8 cm) with the example text
- You type
- Leg shape, Leg width, Leg depth, Extra under cup 1, Extra under cup 2, Extra under cup 3, Extra under cup 4, Label, plus 7 more options for fine-tuning
- Files
- STL for any slicer, plus a Bambu Studio project
Why sellers like it
- Up to four cups, each with its own extra lift from 0 to 30 mm in half millimetres
- A lift under every cup as well, to level and raise the piece at once
- Each leg held in a pocket, so the cup can't slide out from under it
- Its number, its corner (FL, FR, BL, BR) or its lift in mm on the side
- Round or square and rectangular legs, 15 to 100 mm
- The whole set on one plate, in one colour, no supports
Stop the rocking
Folded beer mats and wedges of cardboard slide out and squash flat. These cups hold each leg in a shallow pocket, and each cup's floor is as thick as the gap under that leg, so the table stands level and stays that way.
Measure the gap under each short leg, enter it as that cup's extra, and print the set. The cups are marked so they go back in the right place after you clean the floor or move the table.
Labels
- Number: 1 to 4, for legs you've numbered.
- Corner: FL, FR, BL, BR (front left, front right, back left, back right).
- Lift: the cup's height under the leg in mm, so you can tell them apart at a glance.
- Nothing: plain cups.
Printing tips
- Print all the cups together, pocket up, with no supports.
- The Bambu 3MF prints at the load setting: six walls, six top and bottom layers, 40% gyroid infill. Use the same for an STL.
- In a colour close to the floor or the legs, they disappear.
Selling tips
A small fix that sells to anyone with an old floor: cafés with terrace tables, offices, rentals. Ask for the leg size and the gaps. Pair them with furniture leg risers for raising and caster cups for wheels.
Questions about the leg leveller cups
How do I find each cup's lift?
Stand the table where it lives and rock it to find the short legs. Slide a stack of cards, coins or a feeler gauge under each one until it stops rocking, and measure the stack. That's the extra for that cup; a leg that already touches gets 0. Number the legs (or mark them FL, FR, BL, BR) as you go, so each cup goes under its own leg.
Why put a cup under every leg?
So the table stays level and every leg is held the same way. The lift under all of them is the cups' floor, 3 mm by default; set it higher to raise the table at the same time.
Can I level just one or two legs?
Yes: set the number of cups to one or two and give each its extra. The other legs stay on the floor, so a cup with a 3 mm floor adds 3 mm to its extra; take that off what you measured.
What size should the leg be?
Measure the leg where it touches the floor and enter that; the cup adds 0.6 mm round it so the leg drops in. Raise or lower the room round the leg if your printer runs tight or loose.
How should I print it?
Standing, pocket up, all the cups together on one plate, with no supports. The Bambu 3MF prints them at the load setting (six walls, six top and bottom layers, 40% gyroid infill); for an STL use the same.
Can I sell it?
Yes, on the Seller plan. Each set is made to the customer's measurements, so ask for the leg size and the four gaps.
Ideas for selling it
More in personalised print ideas by occasion. Pricing an order? Try the profit calculator and the other free maker tools.
Sellers also offer
Start selling the leg leveller cups
Type your customer's text, send them the picture, download the print file.
Early Black Fridaythrough Nov 30 (US Pacific time)
The Seller plan at $12 $6 a month
For your first 3 months, then $12. Every design, bulk lists, and the right to sell your prints. Comes off at checkout, no code needed.