Digital 3D print fileDownloads as STL3MF
Phone stand with a name on the front
A desk phone stand that holds the phone up for video calls, with a name or company name across the front, under the phone where it stays in view. Three flat pieces that slot together.
- Clad 2 colours, 1 filament swapColours stacked in layers, like a clad coin: pause and swap filament where each colour starts. No AMS needed.
- Mint Set 2 pieces on 1 platePrints as pieces that slot or press together; the studio shows it assembled.
What you download
name-phone-stand-Sophia-Johnson.stlFor any slicer and any 3D printername-phone-stand-Sophia-Johnson.3mfA Bambu Studio project with the colours set
Digital files only. Nothing is posted: you print it yourself, for you or for your customers.
Single files and the Party pass and Season pass are for personal use and gifts. To sell prints you need an active Seller plan or Seller year pass; prints made while it is active stay yours to sell after it ends. The digital files themselves may never be shared or sold. Read the licence
- Size
- About 110 × 107 × 128 mm (11.0 × 10.7 cm) with the example text
- You type
- Name, Company or title, Phone thickness with case (mm), plus 13 more options for fine-tuning
- Colours
- 2 parts (base, text), so it prints in 2 colours or as one
- Files
- STL for any slicer, plus a two-colour Bambu Studio project
Why sellers like it
- The name sits on the panel under the phone, so it shows even with the phone in place
- Holds a phone up to 7 inches, landscape or portrait, in a case up to 16 mm thick
- Two hooks with a lip hold the phone, and the gap between them leaves the charging port free
- A slot in the panel lets the charging cable bend back out of sight
- Three flat pieces that slot together with no glue, and print in one go with no supports
A name that stays in view
Most phone stands put the name on a strip that the phone then covers. Here the phone sits up on two hooks, halfway up a leaning panel, and the name fills the bottom of the panel underneath. The phone is raised high enough for a video call at eye level, and the name stays in sight whether the phone is there or not.
The panel leans back like an easel. Two side pieces slot into it from above: in front, each has a small hook with a lip that the phone sits on; behind, a long curved leg reaches back far enough that a tall phone, or a tap on the screen, won't tip it. The hooks are set wide apart, so the phone sits square on both, and the charging port in between stays free.
Printing tips
- Print the three pieces flat, face up, in one go. Only the panel needs the second colour, for the lettering at the top of its layers.
- PLA or PETG at 4 mm thick is plenty stiff. Print the side pieces with 3 or more walls, since the hooks carry the phone.
- If the side pieces are tight in the slots, raise slot_fit by 0.1 mm; if they wobble, lower it.
- Set phone_thickness for the thickest case that will sit in it, not the bare phone.
Selling tips
Offer it as a corporate gift with one name per stand and the company name on the second line: on the Seller plan, a bulk order with one name per line gives one file per person. Print the whole team in the company colour, with the names in white. It also sells on its own as a desk gift for a new job, a graduation or a teacher.
Questions about the name phone stand
How is it put together?
The panel has two slots down from its top edge. Each side piece drops into one from above, with its hook in front of the panel and its leg behind. The hooks press the panel back against the legs, so it holds firm without glue, and it lifts apart flat again.
Which phones does it fit?
Any phone up to about 7 inches, in landscape or portrait. Set phone_thickness to the thickness of the phone in its case: most phones are 8 to 9 mm, and a thick case takes it to 12 or 13. The hooks are 56 mm apart, narrower than any phone in portrait, so the phone always sits on both.
Can I charge the phone while it sits on the stand?
Yes. In portrait the charging port sits between the two hooks, and the slot in the panel below lets the cable bend back behind the stand. In landscape the cable comes out at the side. Turn cable_gap off if you don't need it, and the stand gets a little lower.
How big is it, and does it fit my printer?
The default stand is 110 mm wide, 128 mm tall and 107 mm deep, with the bottom of the phone just over 60 mm above the desk. Laid out flat, the three pieces take about 250 by 197 mm, so they print together on a 256 mm bed or a 250 by 210 mm bed. On a smaller bed, or with a wider or taller stand, split the file into objects in your slicer and print the panel and the two side pieces on separate plates.
How is it different from the phone dock organiser?
The dock organiser is one solid block with a pen cup next to the phone, and the styled phone rests are low solid wedges. This stand is three thin flat pieces that slot together and pack flat, raises the phone higher for video calls, and puts the name on a big panel facing you.
Ideas for selling it
More in personalised print ideas by occasion. Pricing an order? Try the profit calculator and the other free maker tools.
Sellers also offer
Start selling the name phone stand
Type your customer's text, send them the picture, download the print file.
Early Black Fridaythrough Nov 30 (US Pacific time)
The Seller plan at $12 $6 a month
For your first 3 months, then $12. Every design, bulk lists, and the right to sell your prints. Comes off at checkout, no code needed.