Digital 3D print fileDownloads as STL3MF
Controller stand with a sunset and palms behind it
A stand that keeps a game controller off the desk and in front of a sunset: a striped sun with two palms against it, a rail across the front with the player's name, and two side rails the controller rests on. Four flat pieces that slot together without glue.
- Clad 3 colours, 1 filament swap across 2 platesColours stacked in layers, like a clad coin: pause and swap filament where each colour starts. No AMS needed.
- Mint Set 4 pieces on 2 platesPrints as pieces that slot or press together; the studio shows it assembled.
What you download
sunset-controller-stand-LIAM.stlFor any slicer and any 3D printersunset-controller-stand-LIAM.3mfA Bambu Studio project with the colours set
Digital files only. Nothing is posted: you print it yourself, for you or for your customers.
Single files and the Party pass and Season pass are for personal use and gifts. To sell prints you need an active Seller plan or Seller year pass; prints made while it is active stay yours to sell after it ends. The digital files themselves may never be shared or sold. Read the licence
- Size
- About 190 × 130 × 173 mm (19.0 × 13.0 cm) with the example text
- You type
- Name, In front of the sun, Sun size, Lettering, plus 7 more options for fine-tuning
- Colours
- 3 parts (base, text, foot), so it prints in 3 colours or as one
- Files
- STL for any slicer, plus a three-colour Bambu Studio project
Why sellers like it
- A round sun 160 to 210 mm across, striped across its lower half, with two palms, one palm or none
- The player's name on a rail across the front, which also stops the controller sliding off
- Fits any controller: it rests on two rails and leans on the sun, and nothing grips it
- Four flat pieces that slot together with no glue and come apart to post
- Three colours with no multi-colour printer: sky, sun and rails, one filament change on the sun's plate
- Room between the rail and the sun, and the gap between the side rails, are yours to set
A sunset behind the controller
A controller left on the desk gets buried, knocked off or sat on. This stand gives it a place, and gives the place a view: a big round sun, striped across its lower half the way a sun looks as it goes down over water, and two palms standing dark against it.
The controller sits on two side rails and leans back on the sun. A rail across the front carries the player's name and stops the controller sliding off.
Four flat pieces
The sun, the name rail and two side rails all print flat. Slots in the side rails take the sun and the name rail, both leaning back a little, and the whole stand pushes together by hand. It comes apart again to go in a drawer or an envelope.
Colours
A deep purple or navy sky with an orange or pink sun gives the look of an evening on the coast. Black side rails disappear under the controller; rails in the sun's colour make more of them.
Printing tips
- Print every piece flat, face up, with no supports.
- The sun and the name rail share a plate: sky colour first, then one filament change for the sun and the name.
- The Bambu 3MF prints it at the sturdy setting: four walls and 25% gyroid infill. Use the same for an STL.
- If the slots are tight, raise the clearance by 0.05 mm and reprint a side rail first: it is the quickest piece.
Selling tips
Offer it with the buyer's name or gamer tag and a choice of sky and sun colours. It pairs with the game case stand for the shelf by the console and a cheat code keychain as the small extra in the parcel.
Questions about the sunset controller stand
Which controllers does it fit?
Any of them. The controller sits on the two side rails and leans back on the sun, with the name rail in front to stop it sliding, so nothing has to match its shape. For a small or a large controller, change the room between the rail and the sun (45 to 80 mm) and the gap between the side rails (50 to 100 mm).
How does it go together?
The two side rails each have two slots. The sun drops into the back pair and the name rail into the front pair, each with matching slots cut up from its bottom edge. They push together by hand, with no glue, and pull apart again.
The slots are tight or loose.
Change the clearance: more if the pieces won't go in, less if they wobble. 0.2 mm suits most printers.
How many colours does it need?
Three, on any printer. The sun and the name rail print on one plate in the sky colour with one filament change to the sun colour for the top layers. The two side rails print on their own in a third colour, or in the sky colour again.
How should I print it?
Everything flat and face up, with no supports. The Bambu 3MF prints it at the sturdy setting (four walls, 25% gyroid infill); for an STL use the same, since the side rails are thin and carry the controller.
Is the sunset copied from a game?
No. The sun and the palms are our own drawing, and the stand carries no game's name, logo or artwork.
Can I sell it?
Yes, on the Seller plan. It posts flat in an envelope, and each one is made to order with the buyer's name or gamer tag.
Ideas for selling it
More in personalised print ideas by occasion. Pricing an order? Try the profit calculator and the other free maker tools.
Sellers also offer
Start selling the sunset controller stand
Type your customer's text, send them the picture, download the print file.
Early Black Fridaythrough Nov 30 (US Pacific time)
The Seller plan at $12 $6 a month
For your first 3 months, then $12. Every design, bulk lists, and the right to sell your prints. Comes off at checkout, no code needed.