Filament color change calculator
Drop in an STL or 3MF. It finds the heights where the model changes, like where raised letters start, and tells you the layer to pause at in your slicer. No AMS needed, and your file never leaves your device.
On this device
Removes saved files, recent plans and your settings for this tool.
Your results show here: the heights where the model changes and the layer to pause at.
Change filament at
Share this plan
The link carries the result, not your file: heights, layers, colors and slicer.
How a two-color print works on one spool
Most two-color name pieces are a base with letters raised on top. Every layer below the top of the base is one color and every layer above it is the other, so one pause does it: the printer stops, you swap filament, it carries on. No AMS, no purge tower, no waste.
The trick is pausing at the right layer. Slicers count layers from the bed, the first layer is often thicker or thinner than the rest, and the number in the slicer is not the height in millimeters. Pause one layer early and the base gets a stripe of the letter color; one layer late and the letters start in the base color.
This calculator reads the model the way a slicer does. It finds every flat face between the bottom and the top, which is where part of the model stops (the top of the base) or starts, and works out the first layer printed above it for your layer heights. It also tells you when a step falls between two layers, so you can fix the layer height before you waste a print.
Add the pause in your slicer
Using layer from the list above. Set the same layer heights in the slicer as here, or the numbers won't match.
Bambu Studio
- Open the file and set Layer height and Initial layer height (Process, Quality) to the values above. Slice the plate.
- In Preview, drag the slider on the right up to layer from the list. The label shows the layer number and the height of its top.
- Right-click the + beside the slider handle and choose Add pause. Do the same for each layer in the list.
- Slice again and print. When the printer pauses, unload the filament from the printer screen, load the next color, let it purge until the color runs clean, pull off the strand and resume.
OrcaSlicer
- Set Layer height and First layer height (Process, Quality) to the values above, and turn off variable layer height. Slice.
- In Preview, drag the vertical slider to layer from the list.
- Right-click the + and choose Add pause, or Add color change if your printer supports M600. Repeat for each layer.
- Check Printer settings, Machine G-code, Pause G-code is filled in for your printer (M601 for Prusa, PAUSE for Klipper, M400 U1 for Bambu). If it's empty the printer won't stop.
PrusaSlicer
- Set Layer height and First layer height (Print settings, Layers and perimeters) to the values above. Slice.
- In Preview, move the top handle of the vertical slider to the layer that starts at the height from the list (layer from the list). The slider shows the top of each layer.
- Click the orange + to add a color change (M600), or right-click it for Add pause print (M601). Repeat for each height.
- Export the G-code and print. The printer stops before that layer, asks for the new filament and carries on.
Cura
- Set Layer Height and Initial Layer Height to the values above, and leave adaptive layers off. Slice.
- Open Extensions, Post Processing, Modify G-Code, click Add a script and pick Filament Change (M600) or Pause at height.
- Filament Change asks for the layer the new color starts on: enter the layer from the list (several layers go in one box, separated by commas). If your Pause at height script asks for the last layer to finish before the pause, enter one less instead. Read the note under the field: it says which one your version wants.
- Close the dialog, slice again and save. The scripts run when the G-code is written, so the preview won't show the pause.
Designs built for one clean swap
Two-color STLmint designs stack their colors in layers, so they print on any printer with a pause at each change, and most need just one: the Clad badge on each design says how many. These all swap once. The Bambu Studio project you download has the base and the letters as separate parts with their own filaments, ready for an AMS, and you add one pause for a single spool. Type your customer's name, check the picture, print.
Questions about color changes
How do I print two colors without an AMS?
Print the base in one color, pause at the first layer of the raised part and swap filament, then let it finish in the second color. It works on any printer that can pause, as long as the colors sit in layers on top of each other. This calculator finds the layer for you.
Which layer do I pause at?
The first layer of the new color: the first layer printed above the height where the base stops. Slicers number layers from 1 at the bed, and the first layer is often a different height from the rest, so the calculator works it out from your first-layer and layer heights.
Can I use this for colour changes too?
Yes, color and colour are the same thing here. It works for any filament swap: a new color, a glow or silk filament for the top layers, or a different material where your printer allows it.
Is my file uploaded?
No. The file is read by your own browser and never sent anywhere. A share link only carries the result (file name, heights, layers and colors), and you can lock it with a passphrase.
Why does it say the change is between layers?
The model changes at a height that isn't a multiple of your layer height, so the swap lands on the nearest layer and the color edge is off by part of a layer. Pick a layer height that divides the height, or redesign the step to sit on a layer line.
Can I change color more than once?
Yes. Tick every height you want and add a pause at each layer. Each swap costs a few minutes at the printer, so designs with one swap are the quickest to sell in numbers.
How much filament of each color will I use?
The calculator adds up the solid volume above and below each change and turns it into grams for the material you pick. That's the most it can weigh: thin name pieces print nearly solid, chunky parts use less because of infill.
Why can't it find a change in my model?
Two colors side by side in the same layers (a flat logo inlaid in a flat plate) can't be split by height. That needs a multi-material printer, or a design that raises one color above the other.
Sell two-color name prints without an AMS
Pick a design, type the name, and download a file that swaps color at one layer.
Early Black Fridaythrough Nov 30 (US Pacific time)
The Seller plan at $12 $6 a month
For your first 3 months, then $12. Every design, bulk lists, and the right to sell your prints. Comes off at checkout, no code needed.