Get ready for reception: name writing and laces, with a name tracing board and shoe tying practice
Two things children are often asked to manage in their first term: writing their own name and doing up their shoes. A name tracing board and a lacing shoe card to practise both over the summer, how to use them a few minutes a day, and selling them to parents and nurseries.
In England, most children start reception full-time in the September after their fourth birthday; in the US the equivalent is kindergarten. The summer before, parents get lists of things that will help. Council and NHS guidance is consistent about the basics: a Westmorland and Furness council list includes putting on and taking off their coat and shoes and getting dressed with little help, and Kent's NHS children's service suggests children recognise their own name written down, since it will be on all their belongings. The same Kent page advises easy-fastening shoes to begin with, so laces are something to practise without pressure, not a skill needed on day one.
Two of those can be practised at the kitchen table with something made for the child. A name tracing board builds the shape of their name before the pencil comes out, and a lacing card gives them shoe tying practice without anyone kneeling at the front door. This post covers both, how to use them in short bursts over the summer, and how sellers can offer them as a set.
Writing their name: the tracing board
The name tracing board is made from the child's own name. The letters are grooves cut through the top layer to a second colour underneath, wide enough for a finger. A small stylus prints beside the board for later.
A groove guides the finger along the letter's path, which a raised letter can't do. It is the same idea as tracing in a tray of sand, without the sand.
Type the name the way the school writes it, usually a capital first letter and the rest small: Emma, not EMMA. The board cuts exactly what you type. Letters are 46 mm tall by default and can go up to 70 mm; the board is at most 246 mm wide, so a long name gets shorter letters. Maximilian comes out a little over 30 mm tall. For a very long name, use the stylus, or make a board for each half.
Stars, hearts, or a sun and a cloud can go in the corners, and a line of small words under the name, such as I can write my name. Names can be in English or Hindi.
How to use it over the summer
The child runs a finger along the groove of each letter, saying its name or its sound. For the first few goes, show them where each letter starts and which way it goes. A few minutes a day is plenty. When the finger is sure of the path, move on to the stylus, and after that to a pencil on paper.
Shoe tying practice: the lacing card
The lacing shoe card is a flat trainer with real eyelets for a real lace and the child's name on the toe. It lies on the table with the heel towards the child, as if they were looking down at their own foot, and the name reads from that side.
A shoe on a foot is far away, upside down and wobbling. The card is in front of them, the right way round, and stays still. Once the knot is learnt there, it moves to the real shoe.
It takes any ordinary lace of 90 to 120 cm. A flat lace is easier to hold than a round one, and two laces of different colours knotted in the middle help with which goes over which. Choose one shoe for the knot alone, or a left and a right marked L and R, with a star on the outside of each, so left and right get learnt at the same time.
The default card is 200 mm long, about an adult's shoe, so the eyelets are well apart. It goes from 150 to 240 mm, with three to seven pairs of eyelets.
Printing them
Both print flat, face up, with no supports, in two colours stacked with one filament change.
- Tracing board: the board first, then the top layer with the letters left open. Strong contrast helps, such as a bright top over a dark or yellow base. Check that the small islands inside letters like a and e are stuck down well.
- Lacing card: the shoe first, then the name and stitching. A bright shoe with white stitching and a white lace looks like a trainer. The eyelets are 5 mm; make them 6 mm for thick laces.
Selling them as a starting-school set
Parents are the buyers before the first term; nurseries and reception classes can order one per child from the register. For a nursery's intake, paste the names one per line into a bulk order. Bulk orders and the right to sell come with the Seller plan.
Send the lacing card ready-laced, with the name on it. A set can grow: the name puzzle for a younger sibling, the learning clock for the year after, and a bag tag with the same name for the school bag.
The post on starting-school toys to 3D print covers the clock alongside these two, and the back to school page has bag tags and name tags for the first day.
Planning what to make next? Browse personalised print ideas by occasion, or work out prices, party orders and colour changes with the free maker tools.