Digital 3D print fileDownloads as STL3MF
Logo click dial: a fidget clicker with your logo
A coin with your logo on it that clicks as it turns inside its ring, with a name or website round the edge. Upload any logo. Prints in place in one go, with no switch, spring or magnet to buy.
- Clad 2 colours, 1 filament swapColours stacked in layers, like a clad coin: pause and swap filament where each colour starts. No AMS needed.
- One Strike One pieceComes off the plate ready to use, with nothing to put together.
What you download
logo-click-dial-SUMMIT-OUTFITTERS.stlFor any slicer and any 3D printerlogo-click-dial-SUMMIT-OUTFITTERS.3mfA Bambu Studio project with the colours set
Digital files only. Nothing is posted: you print it yourself, for you or for your customers.
Single files and the Party pass and Season pass are for personal use and gifts. To sell prints you need an active Seller plan or Seller year pass; prints made while it is active stay yours to sell after it ends. The digital files themselves may never be shared or sold. Read the licence
- Size
- About 49 × 56 × 6 mm (4.9 × 5.6 cm) with the example text
- You type
- Your logo, Words round the ring, Click, plus 8 more options for fine-tuning
- Colours
- 2 parts (base, text), so it prints in 2 colours or as one
- Files
- STL for any slicer, plus a two-colour Bambu Studio project
Why sellers like it
- Upload any logo: PNG, JPG or SVG
- Clicks at every step, either way round
- Prints in place: the coin comes off the bed already in its ring
- No switch, spring or magnet to buy
- A raised rim round the logo and words round the ring
- Soft, firm or hard clicks; 12 to 30 a turn
A logo you can fidget with
Most logo keyrings are a flat tag that sits in a drawer. This one gets turned over in the hand in meetings and queues, with the logo under the thumb the whole time. The coin turns freely in its ring and ticks at every step, either way round, for as long as anyone likes.
How it works
- The coin's edge is a V that sits in a matching groove in the ring, so it turns but can't fall out.
- Three spring tongues cut in the ring each push a tooth into notches round the coin. They click together, 12 to 30 times a turn.
- Your logo stands up on the coin's face inside a raised rim, like a minted coin; the name, website or slogan runs round the bottom of the ring.
Printing tips
- Print it flat as it comes, with no supports: the coin prints in place inside the ring.
- Change filament where the logo and words begin (0.8 mm under the top).
- If the first layer spreads, the coin can stick to the ring: lower the bed temperature a little or raise the fit.
- Thin lines in a busy logo print better with the logo's lines thickened a little (All options).
Selling tips
Ask the customer for their logo as a PNG or SVG and the words for the ring. Dark coins with a gold or white logo look most like a minted coin. For a button to press instead of a coin to turn, offer the push clicker.
Questions about the logo click dial
What logo can I use?
Any picture of it: a PNG, JPG, WebP or SVG. A logo on a plain white or see-through background works best. The studio reads it in your browser, splits it into dark and light, and shows the shape that will print; tick “Light logo on dark background” for a white logo on a coloured square. Photos and soft shadows don't work.
How does it click without a switch?
Three thin tongues are cut in the ring, each with a small tooth on its end. The tooth drops into notches round the edge of the coin, so turning it pushes each tongue aside and lets it snap back: a tick at every notch, all three together. Nothing to buy and nothing to put together.
How does it print in place?
Flat on the bed, no supports. The coin's edge is a V and the ring has a matching groove, both at 45 degrees, so they print without supports and the coin can't fall out. There is a small gap all round; if the coin comes off the bed stuck, give it a firm twist, and if it stays stuck raise the fit in All options and reprint.
How many colours does it need?
Two, stacked. The ring and coin print in one colour and the logo, rim and words stand on top in the second, so one filament change does it on any printer.
Will it wear out?
The tongues bend only a fraction of a millimetre, well within what PLA takes again and again. PETG is tougher still. Choose soft clicks for a quiet desk fidget and hard ones for a loud keyring.
Can I sell these with my customers' logos?
Yes, on the Seller plan. Only put a logo on a clicker when the customer owns it or has permission to use it.
Sellers also offer
Start selling the logo click dial
Type your customer's text, send them the picture, download the print file.
Early Black Fridaythrough Nov 30 (US Pacific time)
The Seller plan at $12 $6 a month
For your first 3 months, then $12. Every design, bulk lists, and the right to sell your prints. Comes off at checkout, no code needed.