Digital 3D print fileDownloads as STL3MF

Logo click slider: a sliding fidget clicker with your logo

A tile with your logo on it that slides along a track and clicks into every stop, with a name or website on the frame. Upload any logo. Prints in place in one go, with no magnets or springs to buy.

What you download

  • logo-click-slider-VOLT-FITNESS.stlFor any slicer and any 3D printer
  • logo-click-slider-VOLT-FITNESS.3mfA Bambu Studio project with the colours set

Digital files only. Nothing is posted: you print it yourself, for you or for your customers.

Single files and the Party pass and Season pass are for personal use and gifts. To sell prints you need an active Seller plan or Seller year pass; prints made while it is active stay yours to sell after it ends. The digital files themselves may never be shared or sold. Read the licence

Size
About 53 × 36 × 6 mm (5.3 × 3.6 cm) with the example text
You type
Your logo, Words on the frame, Stops, Click, plus 7 more options for fine-tuning
Colours
2 parts (base, text), so it prints in 2 colours or as one
Files
STL for any slicer, plus a two-colour Bambu Studio project

Why sellers like it

  • Upload any logo: PNG, JPG or SVG
  • Clicks into every stop, back and forth
  • Prints in place: the tile comes off the bed already in its track
  • No magnet, spring or switch to buy
  • Three to eight stops; soft, firm or hard clicks
  • Your name or website along the frame

A logo that slides and clicks

Fidget sliders are the ones people flick back and forth without looking. This one carries a logo on the tile, under the thumb, and the name on the frame. Push the tile along and it drops into each stop with a tick, then back again.

How it works

  • The tile's long edges are a V that sits in matching grooves, so it slides but can't lift out.
  • A spring tongue cut in the frame pushes a tooth into notches along the tile's top edge, one notch for each stop.
  • Your logo stands up on the tile inside a raised border; the name, website or slogan runs along the frame below.

Printing tips

  • Print it flat as it comes, with no supports: the tile prints in place in its track.
  • Change filament where the logo and words begin (0.8 mm under the top).
  • If the first layer spreads, the tile can stick to the frame: lower the bed temperature a little or raise the fit.
  • Thin lines in a busy logo print better with the logo's lines thickened a little (All options).

Selling tips

Ask the customer for their logo as a PNG or SVG and the words for the frame. Wide logos suit the tile better than tall ones. For a round logo, offer the click dial instead.

Questions about the logo click slider

What logo can I use?

Any picture of it: a PNG, JPG, WebP or SVG. A logo on a plain white or see-through background works best. The studio reads it in your browser, splits it into dark and light, and shows the shape that will print; tick “Light logo on dark background” for a white logo on a coloured square. Photos and soft shadows don't work.

How does it click without a magnet?

A thin tongue is cut in the frame above the track, with a small tooth on its end. The tooth drops into a row of notches along the tile's edge, so sliding the tile pushes the tongue aside and lets it snap back: a tick at every stop. Nothing to buy and nothing to put together.

How does it print in place?

Flat on the bed, no supports. The tile's long edges are a V and the frame has matching grooves, both at 45 degrees, so they print without supports and the tile can't lift out. There is a small gap all round; if the tile comes off the bed stuck, push it firmly from one end, and if it stays stuck raise the fit in All options and reprint.

How many colours does it need?

Two, stacked. The frame and tile print in one colour and the logo and words stand on top in the second, so one filament change does it on any printer.

How big is it?

About 53 x 36 mm and 5.8 mm thick with five stops, plus the key ring loop. More stops make the track longer; the tile width sets the height.

Can I sell these with my customers' logos?

Yes, on the Seller plan. Only put a logo on a clicker when the customer owns it or has permission to use it.

Sellers also offer

Start selling the logo click slider

Type your customer's text, send them the picture, download the print file.

Personalise this design

Early Black Fridaythrough Nov 30 (US Pacific time)

The Seller plan at $12 $6 a month

For your first 3 months, then $12. Every design, bulk lists, and the right to sell your prints. Comes off at checkout, no code needed.

Get the Seller plan