How to change filament color at a layer (no AMS needed)

Two-color prints on a single-spool printer come down to one pause at the right layer. How to find that layer, add the pause in Bambu Studio, OrcaSlicer, PrusaSlicer or Cura, and swap cleanly.

How to change filament color at a layer (no AMS needed)

A name in white on a navy base reads from across a room. The same name in one color, lit from the side, can be hard to read at all. You don't need an AMS or a multi-material upgrade for it: if the letters sit on top of the base, one pause and one filament swap does the whole job.

The only hard part is pausing at the right layer. Here's how to find it, and how to add the pause in each of the big slicers.

Why one pause is enough

Most two-color name pieces (keychains, bag tags, desk plates, cake toppers) are a flat base with raised lettering. Every layer below the top of the base is one color. Every layer above it is the other. So the print goes:

  1. Print the base in color one.
  2. Pause at the first layer of the letters.
  3. Swap to color two and resume.

No purge tower, no purged filament between colors, and on a full bed of tags you swap once for all of them. That makes it the most economical way to print two-color names, even if you do own an AMS.

Finding the right layer

This is where most first attempts go wrong. The slicer shows layer numbers, your model is measured in millimeters, and the first layer is often a different height from the rest. Pause one layer early and the base gets a stripe of the letter color on top. Pause one layer late and the letters start in the base color.

The rule: pause at the first layer printed above the top of the base. With a 0.2 mm first layer and 0.2 mm layers, a base that's 2.4 mm thick ends on layer 12, so the letters start on layer 13.

You can work it out by hand:

  • Layer 1 runs from 0 to your first-layer height.
  • Every layer after it adds one layer height.
  • The change layer is the first one whose bottom sits at the top of the base.

Or skip the arithmetic: our free filament color change calculator reads your STL or 3MF in the browser (nothing is uploaded), finds every height where the model changes, and lists the layer to pause at for your layer settings. It also warns you when a step falls between two layers, which is the other common cause of a fuzzy color edge.

Check the base sits on a layer line

If the base is 2.5 mm thick and you print at 0.2 mm layers, the top of the base lands halfway through a layer. The slicer rounds it, and the color edge ends up a little high or low. Two fixes:

  • Change the layer height so it divides the step: 2.5 mm works with a 0.1 mm or 0.25 mm layer, or a 0.3 mm first layer plus 0.2 mm layers.
  • Change the design so the base thickness is a multiple of your layer height.

Bambu Studio

  1. Set Layer height and Initial layer height under Process, Quality. Slice.
  2. In Preview, drag the slider on the right up to your change layer. The label shows the layer number and the height of its top.
  3. Right-click the + beside the handle and choose Add pause. Bambu's wiki page on the slicing preview confirms the printer stops before printing the layer you pick, so pick the first layer of the letters.
  4. Slice again and print. When it pauses, unload from the printer screen, load the new color, let it purge until it runs clean, pull off the strand and resume.

Our Bambu Studio downloads come with the base and the letters as separate parts on separate filaments, so with an AMS you just slice and print. Without one, add the single pause above. There's more on this in two-colour name prints in Bambu Studio.

OrcaSlicer

  1. Set layer heights under Process, Quality, and turn off variable layer height. Slice.
  2. In Preview, drag the vertical slider to your change layer.
  3. Right-click the + and choose Add pause, or Add color change if your printer supports M600.
  4. Check Printer settings, Machine G-code, Pause G-code has something in it for your printer (M601 for Prusa, PAUSE for Klipper, M400 U1 for Bambu). If it's empty, the printer won't stop.

PrusaSlicer

  1. Set layer heights under Print settings, Layers and perimeters. Slice.
  2. In Preview, move the top handle of the vertical slider to the first layer of the letters. The slider shows the top height of each layer, so look for the one just above the base.
  3. Click the orange + to add a color change (M600), or right-click it for Insert pause print (M601). Prusa's article on inserting a pause notes the pause goes in before the selected layer prints.
  4. Export and print. The printer stops, asks for the new filament and carries on.

Cura

  1. Set Layer Height and Initial Layer Height, leave adaptive layers off, and slice.
  2. Open Extensions, Post Processing, Modify G-Code, click Add a script and pick Filament Change or Pause at height.
  3. Enter the layer number. Read the note under the field: Filament Change wants the layer the new color starts on, while some versions of Pause at height want the last layer to finish before the pause, which is one less.
  4. Slice again and save. The script runs when the G-code is written, so the preview won't show the pause.

Swapping cleanly

  • Purge until the color runs clean. Light after dark needs more: white over black can take a long strand.
  • Pull the strand off before resuming, or it gets dragged into the first layer of the letters.
  • Don't wait too long. On a long pause the bed can cool enough for small parts to lift. If you'll be away, set the pause near the end of the base rather than leaving the printer sitting.
  • Wipe the nozzle if a blob has formed while it waited.

When a pause won't work

A pause swaps color for whole layers. If two colors sit side by side in the same layers (a flat logo inlaid flush in a flat plate), no layer number will separate them. You need a multi-material printer for that, or a design that raises one color above the other.

Designs built for one swap

If you sell personalized prints, a design that's already built for clean swaps saves the layer arithmetic. Two-color designs on STLmint stack their colors in layers, so they print on a single spool, and most need just one pause. Each design page shows the count on its Clad badge. These all swap once:

Or browse every design that prints without an AMS. Type your customer's name, check the picture, and print with one pause. For the numbers side, see how to price your 3D prints.

Planning what to make next? Browse personalised print ideas by occasion, or work out prices, party orders and colour changes with the free maker tools.

Take your next custom order in minutes

Type your customer's text, send them a picture to approve, download a print-ready file.

Start selling

Keep reading