A Hot Wheels display to 3D print: a stackable garage wall with a name, a car park, a peg rail for carded cars and a starting grid plinth

Four displays for 1:64 die-cast cars: garage bays that dovetail into a wall under a name sign, a car park with numbered bays that stacks level on level, a peg rail for cars kept in their packets, and a plinth for one special car that joins into a starting grid. What to look for in a display that grows, how each one joins, how they print, and how to sell them.

A Hot Wheels display to 3D print: a stackable garage wall with a name, a car park, a peg rail for carded cars and a starting grid plinth

Toy cars arrive one at a time and keep coming. Hot Wheels has been making them since 1968, Matchbox for longer, and collectors chase yearly series and rare variants as well as everyday cars. Many displays are made for a collection of a fixed size: print another and it sits next to the first rather than joining it, or the parts are meant to clip together and are too tight to do it without force.

Here are four of our designs for Hot Wheels, Matchbox and other 1:64 cars. Each one grows, each can carry a name, and all of them print with no supports and no multi-colour printer. STLmint is not affiliated with Hot Wheels, Matchbox or any other toy brand; these are our own designs, sized for those cars.

What to look for in a display that grows

  • Joints with a fit you can change. A joint that slides on one printer jams on the next. A clearance setting and a small test print sort it before you print a wall.
  • Bays tall enough for vans and trucks. These cars are sold as 1:64 scale, though brands round sizes to fit the packet. At 1:64 a 4.5 m family car comes out at about 70 mm, so most cars are around 70 to 76 mm long, 30 mm wide and 25 mm high, and long ones reach about 86 mm. Measure the longest in the collection before choosing bay sizes. Vans, trucks and the tall ones need 40 mm or more of height.
  • Shared walls. Bays that share their walls inside one print use less plastic than a row of single boxes.
  • A way to label it. A name sign, numbered bays, a caption under a favourite car.

A garage wall that slides together

The toy car garage wall is the one to start with. Each block is one or two bays across and one to four high, up to eight cars a print. Every car parks side-on in its own bay, so it can only roll along the bay into the walls at each end.

Every block has dovetails along its top and right side and matching sockets along its bottom and left, running the full depth. The next block slides on from the front, beside, above or below. Blocks with the same bay length join above and below; blocks with the same bay height join side by side, so keep the bay length the same across a wall.

  • The bays: 76 to 100 mm long, 28 to 50 mm high and 32 to 46 mm deep. 86 x 32 mm fits the long cars; 44 mm high takes vans and trucks.
  • The fit of the dovetails, from 0.05 to 0.4 mm. 0.15 mm suits a well-tuned printer, 0.25 to 0.3 mm one that prints a little fat.
  • The sign: a name along the top, such as EMMA'S TRUCKS, which slides onto the top block and stops flush with the front. Leave it off the blocks that extend a wall.

Each block has two countersunk screw holes through the back of its bays, hidden behind the cars. Screw every second or third block and let the dovetails carry the rest, or stand it on a shelf with no fixing at all.

A car park with numbered bays

The toy car park is for a desk or a shelf. Each deck has three to six marked, numbered bays, each sunk 1 mm so the wheels sit in it and the car stays parked, nose out.

The decks stack on flat posts, one at each end and a wall along the back, with tabs that press into slots above and below. No glue and no screws. Every deck is the same, so another level goes on at any time: make a set with no name, set it to stand on another car park so it comes with posts for underneath, and start the bay numbers where the last set stopped. A sign with a name stands on top.

A bay is 34 mm wide and 80 mm long by default, with 34 mm of headroom. For vans and trucks, set the bays 39 mm apart, the decks 116 mm deep and the headroom 48 mm. Four or five levels on a shelf is a sensible limit; past that, a drop of glue in the lower tabs keeps it rigid.

A peg rail for cars still in their packets

Some cars are never opened. The carded car peg rail hangs each card by its own hang slot on a flat peg, as the shop did, so the corners and edges touch nothing. The pegs lean up 15 degrees so a card can't slide off, and a title runs along the top: the series, the year, or LIAM'S PICKS.

One rail holds one or two cards, and a jigsaw knob joins it to the next, so the row runs as long as the collection does. Only the first rail needs a title. The pegs are 112 mm apart by default, for standard cards about 108 mm wide, and can go up to 120 mm for wider ones. A peg is a flat blade 10 mm wide and 4 mm thick: hold one of your cards' slots against those sizes before printing a wall of rails. Pegs can be 10 to 100 mm long, for one car or two or three one behind the other.

Measure one of the cards: for a card about 165 mm tall, put the next row 180 to 190 mm below the first and each title shows above its cards.

A plinth for one special car

A few cars deserve more than the box: the first one, the rare one, the one that looks like Dad's. The starting grid car plinth gives one car a lane sunk 1 mm into the plinth inside a painted grid box, with a caption in front: a short number such as P1, 07 or 1968, a title and a smaller second line.

The lane is 92 mm long and 36 mm wide by default, and up to 120 by 48 mm for trucks and haulers. Plinths join side to side with a jigsaw knob, so a row grows one car at a time into a starting grid along a shelf. With joins on, the lane is 6 mm shorter to leave room for the socket.

Which one

Design Best for Cars How it grows
Garage wall A child's wall, a big loose collection Up to 8 a block Dovetails on all four sides
Car park A desk or shelf, play as well as display 3 to 6 a deck Another deck on press-in posts
Peg rail Cars kept in their packets 1 or 2 cards a rail Jigsaw knob, rail to rail
Starting grid plinth One special car with a caption 1 Jigsaw knob, plinth to plinth

They mix well: a garage wall for everyday cars, a peg rail for sealed ones, a plinth for the favourite.

Printing notes

  • Garage wall: on its back, bays upwards. Change filament for the last 1.2 mm to colour the front edge, or leave it one colour. The sign prints face up on its own plate. Print a single bay first and slide two together to settle the fit.
  • Car park: all flat, one filament change a deck for the lines and numbers. The posts print on their own plate in a third colour; try one in a deck before printing the rest.
  • Peg rail: flat with the pegs standing up, one filament change when the rail is done. The Bambu 3MF prints it at the sturdy setting, four walls and 25% gyroid infill, which makes the pegs solid. Use the same for an STL.
  • Plinth: flat and face up, one filament change where the grid box and caption begin. A dark plinth with white or yellow markings reads as tarmac and paint.

Selling them

These sell the way a collection grows: one set with a name, then plain add-ons. All four can be sold on the Seller plan.

For price, look at what printed toy car displays are listed for on the marketplace you sell on, and compare like with like: a plain organiser, a rack for a big collection and a personalised display are different products. Work out your own cost first with how to price personalised 3D prints. On Etsy, remember the listing, transaction and payment fees come off the sale price.

  • Garage wall: a starter block with the child's name on the sign, then plain blocks as add-ons as the collection grows.
  • Car park: a two-level set with the child's name, and single levels as add-ons numbered to carry on.
  • Peg rail: sell it to collectors by the row. A titled rail and three plain ones hold eight cards.
  • Plinth: small and personal. Sell it with the car's name and the owner's, singly or as a grid of five.

They also make a Christmas present for a child who already has a box of cars: a garage block with their name under the tree, with room to add more on the next birthday.

For more for a child's room, see the kids' rooms and learning ideas page, our post on sports name signs for kids' bedrooms and the one on kids' door name plaques.

Questions

Do I need a multi-colour printer? No. Each design needs at most one filament change a plate.

Planning what to make next? Browse personalised print ideas by occasion, or work out prices, party orders and colour changes with the free maker tools.

Take your next custom order in minutes

Type your customer's text, send them a picture to approve, download a print-ready file.

Start selling

Keep reading