A controller wall mount and games room signs to 3D print: a hook with a name, a sunset skyline and a loading bar
A controller hook for the wall with the player's name on it, a name sign with a made-up city skyline at sunset, and a loading bar board that fills by hand for a long game, a savings goal or a reading list. How to set the prongs, how to fix it to the wall, which colours to load, and how to sell them.
A console corner needs a few things beyond the console: a place for the controller that isn't the sofa, something on the shelf that says whose room it is, and a way to see how far a long game has got.
Two things to check before making anything for it. Controllers differ in shape and size between consoles and even between models, so a wall mount that rests the controller on supports, rather than gripping a moulded outline, fits more of them; measure the one it is for. And games room decor is full of game names, logos and characters, which belong to their owners: product names can be trade marks and artwork is protected by copyright, so a piece you sell should carry the buyer's name, not the game's.
Here are three designs for that corner. All three carry a name, print flat with no supports, and need no multi-colour printer.
They are our own designs. They carry no game's name, logo, characters or artwork, and the skyline is made up: it is not a real city's and not one from a game.
The controller off the sofa and onto the wall
The controller wall hook is a plate for the wall by the console, with a name high on it and two prongs the controller rests across. The prongs lean up 12 degrees towards the wall and widen at the tip, so the controller can't slide off.
It holds one controller on a plate about 110 mm square, two one above the other on a taller plate for a shared console, or a headset on a single wide prong.
Setting the prongs
Nothing grips the controller. Its body rests on the prongs and its grips hang either side or below, so nearly any controller fits. Two settings match it to yours:
- The gap between the prongs: 40 to 80 mm.
- How far they stand out: 35 to 70 mm.
Hold your controller against a ruler where it would rest, and set the gap so both prongs sit under its body and the reach so its depth fits on them.
Screws or tape
Two screws hold best, and the controller hides them. Strong mounting tape can work on a smooth, clean wall for a single controller: follow the tape maker's instructions for how long to press it and how long to wait before loading it, and if in doubt leave it longer.
It is not a coat hook, so don't hang bags on it.
Why the prongs come out in the name's colour
The hook prints flat on its back with the prongs standing up. The plate prints first in one colour, and everything above it prints in the second: the name and the prongs. No layer mixes two colours, so any printer makes it with one filament change when the plate is done.
The Bambu 3MF prints the hook at the sturdy setting, four walls and 25% gyroid infill, which makes the 13 mm prongs nearly solid. Bambu's wiki describes gyroid as giving support in all directions, which suits a prong loaded from above. Use the same for an STL.
A name sign for the shelf
The skyline sunset name sign puts a name at the foot of a city at dusk. Nine towers stand in a row with their windows lit, a big striped sun goes down behind them and a palm stands at each end. The name runs along the strip the city stands on.
It is 150 to 240 mm across and takes up to sixteen characters in six typefaces. A long name comes out smaller, so give it a wider sign. Leave the palms or the windows off for a plainer sign.
It prints flat and face up, with one filament change for the sun, the windows and the name. The small windows print cleanly with a 0.4 mm nozzle at the Bambu 3MF's fine-detail setting. The sign leans back in a low foot that prints on its own, with no glue.
A loading bar for a long game
The loading bar progress board is a row of shallow pockets under a title, with a name along the bottom. Each time a step is done, press a tile into the next pocket and the bar fills from left to right. Lift the tiles out to start again.
With ten slots marked in percent it follows a long game from 10% to 100%. It takes four to twelve slots and is 160 to 240 mm across. It leans back 20 degrees in its foot, and each tile sits 2 mm deep, so they stay put. It is not only for games: SAVINGS 2027 with twelve numbered slots, one a month, or READING LIST with eight, one a book.
The board prints with one filament change for the words and the bar's frame. The tiles and the foot print on a second plate in a third colour. If the tiles are tight, raise the clearance by 0.05 mm and reprint just the tiles.
Colours
For the sign, a dark city with a bright sun: purple and orange, navy and pink, or black and yellow. The windows and the name share the sun's colour, so they read as lit. Give the hook the console's colours, and the loading bar green tiles for the classic look.
Selling them
All three are made to order with the buyer's name or gamer tag and colours.
- Sell the hook in pairs for a shared console, with each player's name.
- Show the sign in two or three colourways. It makes a set with the sunset controller stand, which shares its sun and palms.
- Sell the loading bar with the buyer's own title. It goes with the Now Playing case stand as a present for someone starting a long game.
- Fill out the room. The headphone stand is the partner to the hook for a headset that lives on the desk.
For the desk side of the same corner, see our post on a controller stand and game case display. If you are printing for a release night, there is also a post on things to 3D print for GTA 6 launch night. For presents, see gifts for gamers to 3D print with their name and the gifts for gamers ideas page.
Questions
Will the hook fit my controller? Nearly any controller that can rest across two prongs. Set the gap (40 to 80 mm) and the reach (35 to 70 mm) to suit it.
Is the skyline a real city? No. Its nine towers are made up.
Do I need a multi-colour printer? No. Each needs one filament change; the loading bar's tiles print on a second plate.
Planning what to make next? Browse personalised print ideas by occasion, or work out prices, party orders and colour changes with the free maker tools.