Things to 3D print for GTA 6 launch night: a controller stand, a shelf for the new case and keychains for the party
GTA 6 comes out on 19 November. Four things to print in the two days before: a controller stand with a sunset and the player's name, a Now Playing stand for the new case, a cheat code keychain for everyone at the launch party and a plate that says DAY ONE with the date. What prints quickest, which colours to load, and how to sell them to order.
GTA 6 is scheduled for release on 19 November 2026, on PlayStation 5 and Xbox Series X|S, after more than one delay. Release dates can still move, so check the publisher's own announcement before you plan a party or promise a delivery round it.
What to know before printing for a launch
- Don't use the game's name or art. A game's title and logo are trademarks, and its artwork is copyright. Etsy's guide to what you can sell says it can't decide whether a listing infringes someone's intellectual property, and will remove listings when it gets a proper infringement notice. The US Patent and Trademark Office has a plain introduction to trademark basics. The safe line is your own artwork and the buyer's own words.
- Measure the hardware. Controllers and game cases differ in size. Even standard keep cases vary: a typical single DVD case is 15 mm thick and Blu-ray video cases 13 mm, per the keep case article.
- Two days is not long. Pick prints that finish quickly and leave posting out of it if you can.
The four designs here are our own, made for the occasion. They carry no game's name, logo or artwork, and the sunset and palms are our own drawing. You add the names and words. They run from a keychain you can make a dozen of on one plate to a controller stand that gets used every night after.
A stand for the controller
The sunset controller stand keeps the controller off the sofa and the floor. A big round sun, 160 to 210 mm across and striped across its lower half, stands at the back with two palms against it, or one, or none. The controller rests on two side rails and leans back on the sun. A rail across the front carries the player's name and stops it sliding off.
Nothing grips the controller, so it fits whichever one they use, and the gaps can be set for a small or a large one. It is four flat pieces that push together by hand with no glue. A deep purple or navy sky with an orange or pink sun gives the evening-on-the-coast look, and black side rails disappear under the controller.
A shelf spot for the new case
On launch day the new case needs somewhere better than the top of a pile. The Now Playing case stand holds it cover out, leaning back 8 degrees in a slot cut to its thickness, with NOW PLAYING raised on the block in front and a name under it.
The default slot is for a 14.5 mm case. Measure yours to be sure; the slot adds its own clearance.
A cheat code keychain for each friend
For a launch party, the cheat code keychain is the small thing to hand everyone at the door. You type a code as letters: U, D, L and R become arrows, a single letter becomes a round button and a word like START becomes a wide one. Up to twelve presses fit, on two rows if there are more than six. Under the code goes what it does: INFINITE LIVES, SKIP MONDAY, FREE SNACKS, or a guest's name or gamer tag.
A plate that says DAY ONE
The sunset vanity plate is a number plate sign for the shelf or the wall, with a setting sun and a palm beside the letters. Put DAY ONE in the middle, a made-up place across the top such as COUCH COUNTY, and NOVEMBER 19 2026 along the bottom. That is the night written down, as a keepsake.
It is 150 to 250 mm across and leans in a slotted foot or hangs by its corner holes. It is a sign for a shelf, not for a vehicle.
Printing them in two days
All four print flat on the bed with no supports, and none needs a multi-colour printer. Each needs one filament change.
- Keychains last. The keychain is a small, quick print and a plate takes a dozen, so it is the one to leave until the last evening. A dark tag with bright buttons reads best: black with teal, navy with yellow or purple with orange.
- The controller stand takes three colours. The sun and the name rail share a plate in the sky colour, with one change to the sun colour for the top layers. The side rails print on their own in a third colour, or the sky colour again. The Bambu 3MF prints it at the sturdy setting, four walls and 25% gyroid infill; use the same for an STL, since the side rails carry the controller.
- Test the slots on a side rail. It is the quickest piece. If the slots are tight, raise the clearance by 0.05 mm and reprint it before the rest.
- The case stand is one solid block. It prints as it stands, with the filament change a millimetre from the top for the words. The Bambu 3MF uses the weighted setting, 40% gyroid infill, so it stays put; use the same for an STL.
- The plate is the big one. At 250 mm it fills most of a 256 mm bed. 220 mm leaves room to spare. A cream plate with pink or orange letters matches the sunset; the foot prints on its own in any colour.
Selling them before launch day
Everything here is made to order with a name, so there is no stock to guess at.
- Sell the keychains in batches. On the Seller plan a bulk order takes one code and caption per line, so a group of friends each get their own. Offer them as party favours or a small extra in a parcel.
- Pair the stands. The controller stand and the case stand make a shelf set for the console. Ask for the name or gamer tag and the colours.
- Mind the deadline. Two days is tight for posting. Local collection, or a gift that arrives after the night, is the honest offer to make.
- Keep the listing honest. Describe them as a controller stand and a keychain for launch night, not as merchandise for any game.
For more presents along the same lines, see gifts for gamers to 3D print with their name and the gifts for gamers ideas page. The headphone stand and the game controller name sign suit the same room. Our post on a controller stand and game case display covers measuring and assembly in more detail.
Questions
Is this official GTA merchandise? No. These are our own designs, made for the occasion. They carry no game's name, logo, characters or artwork, and the sun and palms are our own drawing.
Will the controller stand fit a PS5 or Xbox controller? It fits any controller, because nothing grips it. It rests on two rails and leans on the sun; for a small or large one, change the room in front of the sun (45 to 80 mm) and the gap between the rails (50 to 100 mm).
Do I need a multi-colour printer? No. Each design needs one filament change.
Planning what to make next? Browse personalised print ideas by occasion, or work out prices, party orders and colour changes with the free maker tools.